Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,
I am using nRF5_SDK_12.0.0 with soft device s130_nrf51_2.0.1_softdevice. I am trying to implement the DFU service in my application, for which I am following:
...
Hello :) I'm trying to run the DFU example (dfu_dual_bank_ble_s132_pca10040) for the nrf52832 chip on a custom board. The Bootloader crashes/resets at the SOFTDEVICE_HANDLER_INIT...
spi.rar
Hi,
As a beginner, I want to combine spi and uart example in nrf52 11.0.0 sdk, for my application. I have included all libraries and driver files from uart in...
Hi,
I would like to ask your support for a very unusual problem that I'm facing with a project based on nrf51822.
The board under test is based on nrf51822, SDK12.1...
Hi all,
I'm trying to set up DFU over BLE - Single Bank using:
Mac OS 10.10.1
gcc 4.9 SDK 7.1 w SD110 7.1.0
PCA10001 v2.2.0
MCP 3.7.1.8567 (modified lib/dfu folder...
I've read a lot of questions regarding the AES decryption using the nrf51 where it was not possible. Is it now possible with the nrf52 or the even newer version?
Thanks,...
this is capture image.
what does that happen?
The debugger is I-Jet and debugging via SWD.
The connection did below. and I'll assume the red line is number one. I...
Hi
I was playing around with the new serialization code in the SDK 13.0.0 and the PCA10056. I was able to compile the connectivity code, but when I try to configure the...
hi, all
I want to run nrf's example named "proprietary_rf->esb_prx", the deafult setting of keil memory is
IROM1: 0X0 0X80000
IRAM1: 0X20000000 0X10000
It can compile...
Hi,
We want to make PCB of NRF52 and we want to buy PCB design software.
Can you guide me that how many layers of PCB is required and how many pins will be required...
I've searched for enabling notification, but there are some points that I can't understand.
GATT characteristic attributes and characteristic cccd values are dedicated...
Hello,
When I check RESETREAS, I have some reboot reasons rised from software error (SREQ).
I know that these errors are not catched in the app_error_handler because...
I am using ARM-GCC (version 6.2 2016q4) toolchain and make command to compile example code.
I have updated my compiler installation path in Makefile.Windows as well.
...
