Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi!
Does Nordic have plans to include any API functionality for choosing an initial scan channel in sequence of jumping over 37, 38, 39 channels?
Currently (SoftDevice...
Hello Nordic,
I tried to debug my board using the JTAG port (P12) on the nRF6310 motherboard. But it's not possible to flash the chip in Keil. I got the error: "Error:...
I use nrf51 DK (PCA 10028) like hardware for sniffer.
I download sniffer software 1.0.1 and flash the dk with help of nRFgo Studio.
I start sniffer.exe and after unplug...
Hi, I'm developing an application for the nRF52832 using mbed and the S132 SoftDevice. Since it appears that the SoftDevice requires exclusive use of Timer0 and mbed uses...
Hi,
I am having 1 central and 2 peripherals. I use ble_app_hrs as the base for both. Sometimes, I dont get the BLE_DB_DISCOVERY_COMPLETE even after I get the BLE_GAP_EVT_CONNECTED...
Hi,
I had some erratic results when I hook these devices via SPI, using a level shifter (e.g. TXB0104) to protect the nRF52. When I look at the schematic for the nRF52...
How I can pairing via NFC with phone? I want that pairing was with a password. I used for exaple project "experimental_ble_nfc_pairing_reference". I used SDK 14 and SoftDevice...
Hi,
I've couple of Nordic Thingy 52.
I was able to connect to these using my Samsung A5 2017 running Marshmallow and see the various sensor readings.
After an OS update...
I am in the process of porting my code from SDK13.0 to 14.0 in order to use s332 v5.0
I can compile and run my application. While it's running, I can see that it is sending...
We are using this device and we seem to have an issue reading from P0.20.
I know this is a dual purpose pin. We have programmed it for input with pullup. We have it attached...
I am currently porting my project from SDK13.0 to 14.0 so I can use s332 v5.0.0.
I receive warnings when compiling
.\_build\nrf52_firmware.axf: Warning: L6330W: Undefined...
I would like to know if it's possible to pair two NRF52832 together using NFC. NOT an android phone to an NRF52, but a central NRF52 standalone connect to a peripheral NRF52...
Hello,
I am using nrf52832 with SDK12 with gcc compiler. I have extended the ble_app_template example with 2 services.
I have 1 timer interrupt using RTC(100 ms) and...
I've been noticing lately when running debugging on my code, a few minutes in it loses connection and says No Source Available for "0x01e054". I'm sure how to even figure...
I am trying to debug a custom version of the bootloader_secure_ble example but am running into FLASH space issues. The bootloader app does not fit into FLASH with -Og optimization...
