It is nRF54L15 + SDK 3.0 + Matter application.
I have developed a custom BLE service that is based on Nordic's proprietary NUS BLE service. The BLE custom service is enabled...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
Hi,
I want to install the nrfgostudio_win-32_1.15.1_installer,but is's fail.nrfgostudio V1.14 can be installed sucessfully.I still use the command line to install the nrfgostudio...
Hi,
Sorry for the noob questions but I'm trying to understand the GPIOTE abstraction and terminology, specifically the events, interrupts and tasks. My understanding is...
Hi
I have a question when I use the l01+.
I donn't use the Auto acknowledgement and Auto Retransmission, interrupt does not reflects on the IRQ pin and leave the IRQ...
hi,
i try to analyze the sdk sample with the standard(Server) ,ie : basic battery service
how to build GATT Requirements and Service Characteristics with the...
Just got the RF51822 PCA 1001 dev board and followed the instructions in SDK 4.4.1 and downloaded the Keil Lite tools from the ARM website.
BUT, didn't realize Keil has...
Hi,
how do I evoke Gazelle on NRF51422? According to specs NRF51422 supports both ANT and Gazelle although on SDK for 51422 the gzll folder is missing. It is present though...
Hi ,
I am using PCA10001 board.
Now i want create 4k buffer in RAM. Which is good way allocate memory to 4k buffer.
Can i use dynamic(malloc function) or static memory...
Assuming the system is composed of one device using nRF51822 and iPhone/PC,
If we want nRF51822 detectable by iPhone/PC so that iPhone/PC can connect nRF51822 when they want...
Hi!
I have been using Bluetooth 2.0 modules for years and now I want to take the step to 4.0/BLE. Previously I used Free2move modules with built in stack. Very simple, make...
I have the nRF51822 development kit (with the new hardware revision QFAA or something), and I am using the Master Control Panel with the new 0.9 firmware for the dongle. ...
Hi in my case,
i pressed gpio button for one time it will do one event.
and for double press it will do another event . how can i do this one,
Regards
Balaji
Hi
In my case i have both 3 gpio interrupts and 4 rtc1 interrupts and have some timer 0 and 1 interrupts
also. how to set priority for all these interrupts in both while...
Hi Guys,
I am planning on using the nrf24l01+ to send data with a payload which is larger than 32 bytes, I was wondering whats the fastest way to transmit these packets...
Hi,
In the nrf51822 SDK examples, there is an example of radio_example which is used for send data and read data. I want to konw that if one module send data and then...
