Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I used nRF24L01+ in an industrial control project that requires low power consumption. I have completed all the functional development and reliability verification. A problem...
NCS 2.6.1 + nRF52832
We are using the LIS2DH sensor driver from Zephyr. We observe (and this is also explicitly stated here ) that the sensor initialization is triggered...
Hi,
I'm trying to use MBEDTLS with MBEDTLS_USE_PSA_CRYPTO and CONFIG_PSA_CRYPTO_DRIVER_CC3XX activated.
Unfortunately I can't find a way to tell MBEDTLS that nRF9151...
Hi, I have cloned the channel sounding with range requestor samples but every time I try to build it I encounter the error:
I have not changed the code or anything, but...
Hello Team,
I'm using nrf54l15 dk and ncs version 2.9.0 for the development. I am getting an error while configuring I2C. I selected i2c20 from the device tree and assigned...
I have been testing the thingy91x and measuring power consumption trying to reduce it to the absolute minimum.
Using a test program that moslty sleeps ( using k_sleep()...
Hello, I need help understanding how MCUBOOT produces signed_by_b0_app.hex file from app.hex on the network core of nrf5340. My goal is to have a DFU updatable hex file (net_core_app_moved_test_update...
Hey everyone! I'm working on my Master's thesis about Rust in embedded systems and trying to figure out how much Nordic Semiconductor actually backs the Rust community.
...
Hi Nordic Team,
Setup:
Board: nrf54l15dk
NCS: v3.0.1
I use LOG_INF and printk to print data in minicom or Serial Terminal v1.4.3 from Nordic. Printings seem misformatted...
Hi, I'm working with the nRF9151 DK and currently going through the Cellular IoT Fundamentals course. In Lesson 4 , it states that we should see a message indicating a successful...
Hi
Could you provide what is the max DCR value of L2/L3 10uH inductor in document "PCA20053_Schematic_And_PCB.pdf" that nRF5340 can be accepted?
nRF5340 datasheet only...
Hello! Introduction. Responsibilities of the cores in my device: 1. app core. 1.1. data processing from a stereo microphone 1.2. data sending to net core. 2. net core. 2.1...
I used to use UICR to store the serial number information during the production with nRF52832.
I am working on new project with nRF9151, but when I check the datasheet,...
