We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Okay so the issue is a little more complicated than this.
Phones used for testing were htc m8 (android 6.0) and lg g5 (android 7.0).
Ble chip running on a linux OS using...
Hello, I'm using this code(observer):
github.com/.../nRF51-multi-role-conn-observer-advertiser
SDK9.0.0
I try to add DFU function, now can enter dfu mode and iPhone6...
Hi Nordic Team,
Can you please share any information regarding Indoor Location Tracking feature/application that nRF52840 can support? does this have AoA/AoD? and can this...
I want to establish BLE connection and have a central device receive data from a peripheral device. I am using the Heart Rate Collector as an example and notice the main file...
Dear All :
Is it possible to creat a pwm with 1sec period?
Since the lowest frequency of the base clock is 125kHz，the top count of the pwm with 1sec period will be 125000...
Hi.
I havent found answer for - in my opinion - common question - how to temporarily change name of ble device on button press. As long as button isnt pressed - advertise...
Hi, I'd like to know if there is a way to subtract two different square waves that are coming from two different input pins and then measure the pulse width (or the frequency...
I have been using Power Profiler Kit nRF6707 for awhile without problem. If I made a mistake by downloading firmware when the PPK is attached to nRF52 DK, the software on...
I followed this tutorial in Infocenter and installed everything infocenter.nordicsemi.com/index.jsp , but I have a problem with Thread examples, programming output looks normally...
Hello,
I am working on nrf52840 EVB , i programmed the board BLE_APP_UART but this profile is not working , still the board functioning previously programmed blinky example...
I'm not sure exactly how to word that,
I am about to try and get the adafruit feather to consume less power in standby and I've been told the arduino library isn't well...
Hello,
I am using pca10028 and sdk 12. I want to use 2 uart for my application but as per datasheet nrf51 has only one hardware uart. Can I implement soft uart on pca10028...
Hi, I would like to measure the electricity consumed at my home(220-240V) with the nrf 51822 and send it over bluetooth. No problem on the bluetooth side, but how can I measure...
I have a buttonless device using a DFU bootloader and ble_dfu buttonless DFU service with SDK v13.0.0. I'd like to make the ble_dfu service available for 5 minutes on power...
Hi Sir,
I am using nordic nRF51822 IC for Tracking Application for that Which antenna is best ?
I have seen two type of antenna .
zig zag pcb antenna
straight...
