After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have studied uart source code.
github.com/.../Android-nRF-Toolbox
And I get confused about the action of reconnection.
AutoConnect flag says It will look up "white...
IOS APP, when in the OTA upgrade, into the background, OTA stopped, at this time into the front desk, can not continue to upgrade, how can you continue to upgrade after entering...
Hi,
we are building a device based on nrf52832. Everyone with the app installed should be able to connect to some characteristics on the device but we want other characteristics...
I have a problem with compiling the blinky example from SDK 12.3.0. I have installed latest arm gcc cross compiler, version 6.3.1. Make command works but on compiling file...
Hello,
I am trying to start nrf52832, when i try to program S132, i stuck in the first step.
i am following the tutorial: devzone.nordicsemi.com/.../
here is my information...
Hi,
I am trying to use the indication to transfer data from NRF52832 device to host. when the indication transfer was comfirmed by host, then we can receive the event ...
Hello,
I would appreciate if anyone can share detailed steps how i can program a custom build PCB with BMD-350 from BMD-350 Evaluation Kit using J-Link OB Interface.
Hi,
I wrote my own nRF24L01+ library for my AVR AtMega2560. I used the datasheet and the widely used Mirf library as my guide. I am happy to say I got it working. I have...
I have a new PC (running 64 bit Windows 7) and am having issues after install nrfgo studio. I had it running previously on another windows 7 (64 bit) machine with no issues...
I noticed that there can be three SPI instances (SPI0, SPI1, SPI2) for the nRF52. Is it possible to have three TWI instances? We have a sensor network that requires 6 of the...
i have used 52832 for pdm clock generater, but i just can set the frequecy to fixed such as 1.032 MHz,1.067 MHz.., if i want to set the frequecy to 1.050MHz, i can't come...
Hi,
I am trying to run LWM2M support based on Contiki OS (contiki/examples/ipso-objects) on a NRF52 (PCA10040) development board. I can successfully build (make TARGET...
I see Nordic release pc-ble-driver 2.0.0 some time ago. I'm using 1.0.0, before I upgrade to the new version, I'd like to know what's new in it....could not find any list...
Hello,
I am using nrf51822 SDK11 S130.
I am using my custom design board which is powered by 12V. The nrf51822 is provided with 3.3V. I used 27k and 9.53K resistors in...
