Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
Hi,
we are using the nRF5340 with the nRF21540 (Fanstel BT40N module). I understand that different regions allow for a maximum of +10 dBm or +20 dBm in transmit power dependng...
Hi All,
In reference to my earlier ticket( https://devzone.nordicsemi.com/f/nordic-q-a/120183/question-on-immutable-bootloader-support-for-nrf54l15 ), I see SDK version...
I am using custom board with MDBT53 and I'm stuck at a point where board does not even let me to connect the debugger so that I can refresh firmware.
I added MCU boot code...
Hi, I have changed Vdd from 1.8 V to 3.3 V but now I cannot flash anymore my board (nrf5340). This is the output error:
* Executing task: nRF Connect: Flash: AppCore_RHS_SD_UI_v1B...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
I have a USB HID device using the 'old' USB stack in Zephyr. I have configured the 'CONFIG_USB_DEVICE_REMOTE_WAKEUP'
1. I put the HOST to Suspend
2. The NRF52 USB goes...
Hello together, Which configurations or setup on the side of the Nordic nrf9161 DK has to be done to use the DEBUG IN connector for SWD? The board is powered by the 5VIN pin...
Hello,
In ncs, I am working with \nrf\samples\ipc\ipc_service. I want MCUboot to build \nrf\samples\ipc\ipc_service\remote to run on nrf5340 CPUNET. When I CONFIG_BOARD_ENABLE_CPUNET...
Hi,
I am working on Temperature sensor MAX30208 using nrf52840 using zephyr. i am working on ncsv3.0.0 . I want to develop a driver for max30208 . can anyone guide me how...
I am trying to get the BMI270 working with a nrf5340 DK. I have read Unable to Connect nRF5340DK with BMI270 Over I2C - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi...
Device Information
Module: FANSTEL BC832 Bluetooth Low Energy 5 Micro Module
Chip: nRF52832
Firmware version: Default AT firmware
Current MAC Address: ef30:0a:cab132...
Hello Sir,
I am currently working with the nRF52832 (for testing purpose, later will use nRF52833 for final product) as a central device using the nRF Connect SDK. In my...
I have been working with 2.9.1 but went back to a project using 2.6.1 to flash a nrf5340dk and can still compile it, but now cannot flash the nrf5340dk. I am getting this...
Hello everyone. I am trying to develop a emulator for a Bluetooth low energy tv remote using raspberry PI. Basically I want to be able to use the raspberry pi as a TV remote...
