Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Hi, I'm using nrf51 without ble.
I want to update flash but not want to delete PAGE every time.
NRF_NVMC->ERASEPAGE = (uint32_t) page_address;
How can i do?
We use IOS DFU toolbox to upgrade firmware with BLE device. we can upgrade successfully with Android, but always failed with IOS.
wrong code is: DFUErrorReadingVersionFailed...
Hi, it's probably a very dumb question, but i don't seem to find any details about it. In nrf52 SDK documentation, in Error Module section it says
The behavior of the...
Hi friends...!
I want to put dynamically changing MPU data into the advertising packet. I am putting my accelerometer data into manufacturer specific data field of ble_advdata_t...
How robust is the output PA of the nrf905?
Assume the ouput matching network and 50Ohm connector is used as in the 868Mhz application note.
If the antenna is removed...
Hi,
I'm trying to find a way to speedup the upload procedure of an application, via BLE on a Arduino Primo with the DFU service.
Here you can find my code:
https://github...
Hi,
I am using ble_app_uart sample code for testing. In that I want to store the incoming data into to three buffers and simultaneously sending this over BLE. i.e., consider...
hi i m using nrf52832 for detection acceleration , angular speed and detection of magetic field with GY-87 ( MPU 6050 and Hmc5883). in fact i wrote a program that read only...
Hi,
I am using s130v2 and running the example code from: nRF5_SDK_12.3.0_d7731ad\examples\ble_peripheral\ble_app_hrs\pca10028\s130\arm4
This is the only modification I...
Hi,
I know this is a Bluetooth 5 spec question, but wanted to know the practical figures for current consumption when nrf52840 is used as both central and peripheral...
Hi,
We are expecting many of our devices to be in close proximity. How can we be certain that when a user initiates a buttonless DFU, that they are uploading to the correct...
Hi,
I thought central is the one which fills up its look up table with 16 bit IDs to keep track of the peripherals. If multiple devices can act as central at the same time...
I am trying to re-base my SDK package, and when I started off with the ble_app_template project for the pca10040 s132, I copied my main file on top, everything compiles just...
I am developing an application which involves control of a brushed DC motor with a quadrature encoder. According to this post, in SDK 12.2.0 - which I am using - it is possible...
