I am using an nRF52840 USB dongle to sniff some Zigbee packets for a product I am developing. I am trying to use Wireshark to decode the messages shared. I followed the steps...
Hi,
My project is based on NRF52832 with SDK11.
I got 2 working units, 1 is advertiser and 1 central.
The advertiser is advertising every 2 second.
The central unit...
Hi,
I have set up a destination in the the NRF Cloud Message Routing Service
The destination has been verified and I can successfully send the test message from NRF Cloud...
Hi,
I was looking at integrating a speaker in my design and i have a class d amplifier that takes in an analog signal which i want to feed directly from the chip. I wondered...
Hello,
I am using SDK v2.9.1 for a Bl653 (NRF52833) and was trying to use the Nordic Academy Example for how to setup the SPI bus. The Nordic Academy example states we must...
I'm currently working on configuring the nPM1300 used in our custom board. In the product spec v1.2, it supports 2 USB compliant current limits, IBUS at 100mA and IBUS at...
Hi,
I am currently trying to enable the GPIO output interrupt functionality on my nPM1300ek with an STM32. However, I am unable to get it work correctly(I was only able...
Hi,
i have a generell question. First i have to say i am not the best programmer, but maybe some one with more experience then me could help me.
Does it make sense to...
Got nRF51422-EK.
Followed instructions and used nRF51 SDK v6.1.0
LED next to the Segger part blinks constantly.
If i build and download Blinky, the LED0/1 do not alternate...
I am developing a platform using C8051F931, MPU9150 and nRF8001. I have re-written the hal code to target the C8051F931 and verified it using the ACI demo test (the echo test...
Hi,
I'm using nrf51822, pca10001 board. I have loaded the uart_example and that worked fine, but using the radio_test_example from Board/nrf6310, that compiled and programmed...
Hello,
I'm new to BLE. I am using nRF51822. Is it possible to modify calling frequency of nus_data_handler() so that I can deal with data coming from BLE faster?
How can...
I see that Digi-Key has two part numbers for the nRF51422-QFAA:
But I don't see any reference to "V2" part number field in the nRF51422-PS document.
What is the exact...
Currently I am set timeout to one second and then on BLE_GAP_EVT_TIMEOUT:
modify data
advertising_init();
advertising_start();
Are there more correct ways...
Hello,
I've connected the nRF8001 module and a light sensor to a microcontroller.
Actually I can read data only when I send a string from my smartphone but I want to...
I'm able to program the Soft Device (s110_nrf51822_7.1.0_softdevice.hex) from nRFGo studio and the compare is fine, but when I go to Keil uVision 5, I can build ble_app_beacon...
I use S130 on two nrf51822/PCA10001 boards. Each nRF scans and advertises simultaneously.
Scan parameters are:
scan_param.active = 0;
scan_param.selective = 0;
scan_param...
Is there a port of lib_aci for 16-bit processors? The structs in lib_aci written for nRF8200 are byte misaligned using a 16-bit processor. Seems to be almost a complete rewrite...
Hello,
I try to generate 4 PWM signals on an nRF51 DK board, but I have two troubles :
in the "Simple PWM", during nrf_pwm_set_value() function the TIMER is stopped...
Hi,
I recently ordered a usb dongle. It has PCA10031 board. The chip shows "N51422 QF ACAB" printed on it.
What SDK should I use? 6.1.0?
What board file should...
Hi!
I am using nRF51 SDK v6.10. I try to analysis the "spi_master_example". Source codes is
working well. But I couldn't understand how the "spi_master_send_recv_irq(...
