I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hi,
I asked the same question but it was a long time ago and still I don't know how to solve this issue. I got a reply but It wasn't help so now I'm writing again with...
Hi
I am new to the nRF kit and C, but I have a project where I shall use the nrf51822 as master and MCP3201 ADC as slave. The nRF is only going to read values that i give...
Hey! I've been working on triggering DFU from within my application. It's obvious that the bootloader in the new SDK has been written to support this but I had some problems...
Hi,
I need the softdevice to be able to receive and send data on it's own without necessarily connecting to iPhone or anything. So:
device1 (nrf51822 receive and send...
nrf8002-based loss prevention solutions are being developed.
our often experience intermittent connection to iOS 7.
Disconnection from the moment after a successful...
There seems to be a lot of questions recently that are re-hashes of previous discussions.
Many discussion forums post a sticky etiquette thread. Can we maybe have something...
The nRF51822 only has one UART and my app needed two. One for a GPS receiver and one for a simple terminal command line interface. The UART RX is interrupt driven, but TX...
Hello,
We are developing using the S110 and having major trouble re-establishing Bluetooth connections to our device. The reason we need to reconnect to our device is to...
Hi all,
I found something different between SD6.0 and SD7.0:
1.KB bonds with iPad successfully;
2.Click OFF the bluetooth button in iPad setting, then KB goes into...
I'm trying to get the ble_app_hsr example working with BLE_DFU_APP_SUPPORT enabled. I have included:
ble_dfu.c
dfu_app_handler.c
bootloader_util_arm.c
But when I build...
I'm using a nRF51422 with the s310 stack. I copied code for adding a custom service that was working with a s110 stack, and tried to add a service to the BLE in the s310....
Hi,
We are a couple of students from Norway trying to get RSSI from an active RFID system we got from ebay.
We have now connected the tranceiver module to our PC running...
Hai,
I am using nRF51822 development kit. I want to test the demo app for S130 soft device using this. But i could find that the demo app is for the evaluation kit. I am...
Hello,
I'm learning how to use s110 and the debugger. I am porting the hids_keyboard app from the PCA10001 to the PCA10003 (nrf51822 -> nrf51422).
As described in this...
I am installing nRFTools_6_1_0 and I get this error during the instalation.
I am trying to connect via USB the PCA10001, but my windows 7 says that the driver is missing...
