When my peripheral calls sd_ble_gap_phy_update, setting rx_phys and tx_phys to BLE_GAP_PHY_AUTO, I receive the BLE_GAP_EVT_PHY_UPDATE event with a status of BLE_HCI_UNSUPPORTED_REMOTE_FEATURE...
Hi,
I recently checked support of MCUBoot validation and from NSIB for nrf54l15. (sdk 3.0.0 and above)
During this, I enabled Signature algo as ecdsa-p256.
And...
How to prevent storage partition from erase durning MCUBOOT firmware update?
I use Settings with NVS to store data
CONFIG_FLASH_MAP=y
CONFIG_FLASH=y
CONFIG_SETTINGS...
Hi,
I am building a Thread network ( www.youtube.com/watch with a Rasp Pi 4 as a border router, an nRF52840 DK as an RCP, and an nRF5340 DK as a child to be added into the...
We found a problem with a client's legacy design. They use two 12 pF load capacitors for the 32 MHz crystal, which has a 4 pF capacitance. This is a somewhat unusual Abracon...
Hello DevZone,
I have a project where I currently use the AT%XPOFWARN feature, in order to turn off the modem in case the battery voltage is too low. It's used in both cellular...
What is the designed (/actual/required due to the specification) behaviour of the Bluetooth stack S110 when notification packets are queued and the CCCD controlling the attribute...
I am looking into using Internal RC instead of External Oscillator (with softdevice on).
The function ser_app_hal_hw_init() uses Xtal clock source by default.
...
Hi, everyone. What is the meaning of datasheet "section 8.5.7 Antenna matching network requirements"->15+j85 ?
Whether is that we can caluate the 50o with the data?
bonjour , j'ai essayé de communiquer deux pca10028 en utilisant l'exemples " transmitter_pca10028 et receive_pca10028 " mais l'experience a echoué je sais pas pourquoi sachant...
Hello,
I'm testing current time service client example on SDK 8.0.0 with iOS.
After connected the devices, iOS show confirmation to pairing.
When I canceled this or...
After enabling and starting the watchdog timer (RR0), how can it be disabled?
This following code does not work :
NRF_WDT->RREN &= ~(1 << WDT_RREN_RR0_Pos);
Neither...
Hi,
I use s120 stack and ble_app_multilink_central
I use function sd_ble_gattc_primary_services_discover(p_client->conn_handle, start_handle, NULL) for discover services...
The sniffer software doesn't seem to find the device on either of two different PCs here, and I'm not sure what we could be doing wrong.
The installation steps were the...
Hello,
I have recently got a n5 start kit nRF51422. I went through all the set up procedures in the user guide, installed all the correct programs/drivers etc.. My unit...
Hello.
I am looking at the schematic of the nRF51422 USB dongle development kit. The pin P0.30 of the microcontroller is attached to ground. As the pin could potentially...
I'm writing a PC utility in Visual Studio to connect to BLE devices. I'm using the PCA10000 and MasterEmulator.dll. I'm able to discover the services and characteristics of...
Hi NORDIC
I download the example of multilink central (S120) into nrf51822 . I do not know why it can not work ? My SDK is s110_nrf51822_7.0.0_softdevice . Please help...
i am very confused about how to count pulse by using nrf51822? I am going to make a heart rate counter, but i don't know how to config registers to achieve this function....
I can't get a simple application, no soft device, to debug on the nRFDK 10028 board using the I-Jet. I am using the debug in and powering the device from an external power...
