Beginner here .. steep learning curve for Nordic ... trying a project with I2S. Took half and hour with an ESP32, but many many hours later, no joy with Nordic.
Working...
Hello. I use the function zb_zcl_finish_and_send_packet to send data from ZC to ZED and it works but one problem is that we're using a rather slow poll (20 seconds) to enhance...
Dear Nordic DevZone,
I'm encountering pairing issues with mobile devices and a nRF54 DevKit flashed with HCI over UART firmware. After initial pairing, deleting the bonding...
Hi, i have locked my beacon with the write_lock characteristic and now i want to unlock the beacon with the lock code which is hard coded in my code. but i was unable to do...
Hi,
I recently updated Nordic connect SDK and toolchain from v2.7.0 to v3.0.1. When compiling my application with activated CONFIG_BT_LL_SOFTDEVICE flag, I get this error...
Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
I don't have found CONFIG_OPENTHREAD_FTD feature in the bulb project prj.conf or prj_release.conf file, but I have found that it is enabled in the final .config file within...
Hi, i have been trying to get GPS and HTTP to be able to work with eachother, but im having some struggles.
After the GPS starts, the program begins spewing out "Invalid...
Hello,
I have exercised the flash driver and that is working fine. I want to save a certain value into a specific address in NVM and I want that part of the .hex file. I...
I just upgraded to SES 4.42 from 4.30a and I'm getting the following compiler warning for file zigbee_cli_cmd_ado.c "Taking address of packed member of struct zb_af_simple_decs_1_1_s...
Dear Sirs,
I am using example anr_hrm nrf_sdk_15.3.0 I would like to use PINs on/off
software s212
#include "nrf.h"
#include "nrf_gpio.h"
#include "nrf_delay.h"...
Dear All,
I am using (nRF52840) in one of my design.
Application program we have taken examples\peripheral\usbd_ble_uart\pca10056\s140\arm5_no_packs code as base code...
Hi,
Good Day!
Statement of Problem: We are using SPI to transfer data to custom LED matrix which uses HT1632C led driver. For strings more than 7 character length we used...
I want to integrate nrf mesh serial example in light Switch example to configure other un-provisioned node
I am using following nrf SDK: >> nrf : nRF5_SDK_15.2.0_9412b96...
Hello,
We have evaluated Smart Remote 3 example code .We migrated that code in the segger embedded studio but we are getting lots of error related to files and libraries...
Hi, I have nRF9160DK and Thingy:91. I want to store APN configurations in the modem but I can't save the APN. Currently, I am giving the APN information manually every time...
Hi
I have nrf82540 dev boards. I loaded one board with Proximity example (SDk Version: nRF5_SDK_15.3.0).
According to your web page: https://infocenter.nordicsemi.com...
I am working on a project that needs to be a ble central and peripheral. I based my development off the experimental/ble_central_and_peripheral/ble_app_hrs_rcs_relay however...
Dear Sirs, good afternoon
I am working in a design that includes an nRF52840 as main processor.
I need to know if it is possible to have the following peripherals implemented...
Hi,
How do we fuse the debug port on nRF9160? The purpose is to block all access and the ability to erase all from outside.
This is my understanding:
From debugger...
My nrf9160 connects to AWS when using the AWS FOTA example. However, when I start the custom job as setup from the following link:
https://developer.nordicsemi.com/nRF_Connect_SDK...
