On future revisions of the nRF52840 Dongle, and on future development hardware of a similar form factor, I'd recommend putting a debug connector that's compatible with the...
Hello,
I am trying to measure nRF9151 current using Power Profiler Kit II, running Cellular UDP project on EVK and following the steps in:
https://docs.nordicsemi.com...
Hello,
We are working on an NRF5340/NRF7002 based project with NCS 2.7.0 SDK. We have been able to get Amazon Root CA 1 and 3 working with the following .conf:
Now...
Hello,
I am working with the nRF7002 DK board and attempting to use the "Light Bulb Matter" example from Zephyr. I am encountering issues when trying to connect the board...
Hi
Our present build system on v2.6.1, builds variants of our baseline application using batch files.
It ends up building using west in this way:
The generated...
We are developing a very low power product. In some cases like not getting registered, PSM not being available, ... we want to drop the connection and go to a sleep state...
I've been following the information on the nRF54H20 with interest as it is most likely the natural candidate for upgrading our existing design. However, I have been waiting...
I am using GPIO interrupt event.
And I added the following code because I wanted to observe PA / LNA.
Adding this code stopped the GPIO interrupts.　Can the two coexist...
Hi,
For nRF82540 dev board, the secure bootloader code has embedded many NRF_LOG_DEBUG(...). But they are not displayed or output to virtual COM port. Is there anyway to...
Hi all,
I'm looking to develop a proprietary start network that may support around 30 devices, with very low bandwidth (pretty much just a keep alive and a sensor state...
I just came upon a blog post from ARM about the use of the Cortex-M4's FPU:
https://community.arm.com/developer/ip-products/processors/b/processors-ip-blog/posts/10-useful...
Hi, I am looking for sample code that can reconnect to bonded devices and share the encryption keys with DFU-OTA.
I have worked using DFU-OTA (JUST_WORKS option); I question...
hi all,
i can't update new nrf cloud certificate
"There was an error generating the certificate: No Nordic product with device id nrf-xxxx...(imei)and ownershipCode...
Hi.
I have a Thingy91 that I will use as a remote wake up for another system. I am trying to estimate how long the system will be able to run on a single charge with the...
Hi!
I am trying to find an example project for the Rigado BMD-340 eval board, or some guide to getting running with this board. We are working on a new product using BLE...
Hello,
I am using peer manager to handle security and bonding. Everythin works fine (bonding witth MITM).
However, when a known peer connects, I am getting 6 (six) PM_EVT_PEER_DATA_UPDATE_SUCCEEDED...
I want to make The Thingy91 a bluetooth peripheral device . I want it to send the generated temperature data to cloud or another device. How do I do this? I had problems with...
Hi Nordic Team,
Please share logic to scan specific peripheral devices which are advertising with a filter other than filter for device name, uuid, short name and MAC address...
Hi,
I am using nRF52832 with SDK v16 with s112 BLE stack.
I am trying to enable the DIS service like below:
The device can boot successfully but when I checked the...
Hello,
I want the scanner to receive both AUX_ADV_IND PDU event and AUX_SCAN_RSP PDU event for the case when AUX_SCAN_RSP PDU will be lost I still want to have AUX_ADV_IND...
Hi,
I am using RTT log with nRF52832, my question is when debug port is disconnected, what will happen to RTT logger?
Will they be simply ignored? or will the debug pins...
Hi.
I want to measure the current on the nrf 52840. I have downloaded the beacon example on the board and I want to measure current when the beacon is transmitting(LED 1...
