Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
I am using DSK 15.3, SES 4.30 with SD 132. The base example I am using is the ble_app_uart_c and I am adding the PWM function to drive a simple piezo buzzer.
The pwm_library...
I am looking for a way to interface with the onboard Bluetooth on the Thingy 91 as well. None of the examples (Peripheral NUS, Central NUS) etc currently work with Nrf52840_pca20035...
We have a need to verify an secp128r1 ECDSA signature. I see that this is not one of the curves supported by the CC310, but I'm looking into creating the CRYS_ECPKI_Domain_t...
The documentation says "This module is ONLY for debugging purposes and must never be used in final product". I know in an ideal world all possible errors are handled and device...
Hello, we are developing a system that will include an nRF52832 in peripheral mode, that will be connected to from a maintenance App (or something) on a mobile phone,and will...
Hi support team,
I'm using sdk 15.0 and softdevice s140_nrf52_6.1.0 and nrf52840.
My application has strict requirements on power consumption, so I have to set advertising...
It seems like this should be a simple thing, but I can't find an example of it, and nothing I've read here seems to help.
I want my app to come up in general advertising...
I'm working with Fantel's adaptation of the nrf52840 (EV-BT840F). I have gotten the GFX example working with Adafruit's ILI9341 in SPI mode, however I am having a problem...
Hi,
How do we detect network detach in nRF9160 in a general way?
We use lte_lc to connect which blocks until we have connect/attached to the network. But how does lte_lc...
Hi,
I have a little program that is built on top of the USB CDC ACM example. This little program waits for an SPI event, when the event arrives, it reads the SPI peripheral...
Hi,
For my project I use a ble central and a ble peripheral.
I have to send data from the peripheral to the central and i use hvx indication to do that.
I have two charactics...
Hi,
I am working on the asset_tracker application.
I have integrated the "lte_ble_gateway" into the asset_tracker application and able to get the BLE values from nRF52840_PCA20035...
I am trying to use PPI to control an output pin. I am successfully using 2 PPI channels at the moment to use the COMP to do freq counting over a 10mS time period. I have added...
We have our first prototype ready and were measuring the power consumption. During development the values seems to be wrong.
So I just added a voltmeter to the DUT out clamps...
I'm having the issue of where calling app_usbd_cdc_acm_write() more than once within the ble_nus_data_handler fails.
A test case is based on the "examples/peripheral/usbd_ble_uart...
