Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
When starting up the device with the nRF5 SDK 3.2.0 for mesh, even though the model and subscription list state is loaded from flash, it is stored again right afterwards....
To the kind attention of Nordic support team,
I was reading this blog https://www.ericsson.com/en/blog/2017/12/wake-up-radio--a-key-component-of-iot
May I ask if Nordic...
After Downgrade protection in the NRF9160 has been set with AT%XPRODDONE=1, switching it off with AT %XPRODDONE=0 returns ERROR. Is there a way to disable downgrade protection...
Hello DevZone,
Is there a way for hardware to update the timer capture register?
I want to create different frequencies using a single timer. Next to the timer, Bluetooth...
I am using Nordic proprietary RF receiver and transmitter. I want to display the received data on my serial terminal using UART pins (any 2 pins as Rx-Tx) .
When I tried...
Hello,
i'm writing a code for NRF9160DK where i plan to send a HTTP POST request to a test server when i push BUTTON1 on DK. To achieve this result i studied separately...
Hello,
I have an issue since today. Indeed I worked for a few weeks on the nRF52840 and everything was alright. I used a dock to connect the nRF52840 by serial port with...
Hi,
I have an application where an nRF52840 DK(1.1.0) is configured to work as both central and peripheral. I want to set a lesser duration for advertising with whitelisting...
I have added lbs_service from ble_app_blinky service within ble_app_glucose example. I made changes in main.c and EMPROJECT File accordingly. I have added ble_lbs.c file in...
I need help in implementing Monitor Mode Debugging (MMD) using Segger Embedded Studio development. Can you please provide detailed help and explanation please?
Hi Devzone:
After searching through the forum I found out that nrf_fstorage_write can only make 1 to 0. So each write needs an erase operation preceding it.
But erase...
Baseline: CLI example on the 52832 with SDK v15.3
I assume the issue will be some more undocumented fix.
sdk_config.h
main.c from the CLI example (UART backend...
I was previously working on nRF51822 ble beacon, in which codes flash of hex 20006.
But i wanted to flash a code nRF5_SDK_11.0.0_89a8197\examples\ble_peripheral\experimental_ble_app_blinky...
Dear Team:
Hi team,I just want to know:
1.Can the ESB protocol call the frequency hopping of Gazell? Is there a corresponding description and source code?
2.Can the...
Hello there, I know that softdevice supports up to 20 connections at the same time, but we need more actually.
If i implement a SPI ram to device, is there any change...