Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi all,
I am trying make some temperature sensor with Segger and nRF52 based on Mesh BLE v4.0.
Currently I am researching documentation and examples to pick best solution...
I'm trying to use the information from this devpost: https://devzone.nordicsemi.com/f/nordic-q-a/39629/how-to-send-data-to-all-node-over-mesh
However, my remaining questions...
I would like to see an example or documentation about how to set my nRF52 DK into various sleep modes. I know that calling "sd_power_system_off()" will turn the device into...
Hello how are you?
I don't speak English very well but I have a doubt about using mesh and nfc simultaneously.
I'm using the Nordic-Thingy52-mesh-demo example - (Nordic...
Hi, team
I am using nRF5_SDK_15.3.0_59ac345/examples/ble_peripheral/ble_app_ancs_c sample application. and i wnated to add extra notification attribute.
added BLE_ANCS_KEY1...
As I understand from documentation current limit for nRF PPK is 70mA. This is when PPK automatically sets measurement range from 1 o 70mA. My question is: Is there a way to...
1、Demo position：Nordic\nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral\ble_app_uart\pca10056
2、I find when the code execute the function of timer_start_op_schedule,the CRITICAL_REGION_ENTER...
Hello,
Using this link ( https://devzone.nordicsemi.com/f/nordic-q-a/35675/how-to-use-static-passkey-for-a-no-display-no-output-peripheral ) I'm able to add passkey protection...
Hi,
i have found similar posts on the forum but could not find the answer. Therefore,I think it is necessary to raise this question again.
problem: platform:nRF52832 and...
Hello there,
I have been testing on nfc-uart example of SDK 13.3.0. I am trying to pass the buffer of 258 bytes to pointer "p_pdu" and its size of 258 to "pdu_lenght". ...
We would like to have that all communications, programming, and supply related TPs and SBs should be kept for debug purposes. Otherwise, we would like to remove all unnecessary...
We're working with the NRF5340 PDK, and it's a pretty big library change from the old SDK. So far I've been unable to find out where to configure the bluetooth PHY and link...
Hi everyone,
The task is as follows. I set up data transfer using notification. I transmit ~ 83 kB in ~ 10 sec. The connection interval parameters are as follows:
The...
Hi Guys,
I flashed the ble_app_uart example available in nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_uart\pca10056\s140\ses location to NRF52840 DK board. In...
