Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
downloaded thingysdkv210 from thingy website. extracted that file and executed Prerequisites as per the procedure
downloaded Python v3.xx.xx
downloaded Git v2.xx.xx
...
Hi,
I am trying to add CLI Command feature into the example Open_bootloader_usb_mbr, but get error during link stage when compile as below,
Building ‘open_bootloader_usb_mbr_pca10059_debug...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
I am using multiple interrupts. For example, BLE communication interrupt and SOC interrupt. I set the priority of each interrupt...
Dear Sir,
I have flashed 'ble_app_hrs' code to one of my RIGADO DK.
I have installed nRFConnect App in mobile phone.
When I press the scan button I could see the device...
Ok I am using GPIO interrupt and want absolute power saving but when I set the GPIO_INTERRUPT_HIGH_ACCURACY to true it works fine but when I set GPIO_INTERRUPT_HIGH_ACCURACY...
Hello,
I want to use P0.27 as output but no way to get it working (tested on my custom board and on DK). If I just change for another pin to check my code, it's OK.
It...
Hi,
I am using nRF SDK v16 with nRF52DK (pca10040) development board.
I've chosen to use RTT logging and I can see my app logs in JLinkRTTViewer window --- however, I...
Hello!
I am developing a FreeRTOS application for nrf52832 with S132 Soft device
Recently I ran out of ram and checked the map-file for clues. The large posts in the mapfile...
Hi,
I don't understand why the characteristic FitnessMachine Feature : (0x2ACC) is not decoded as a bit field by nRF Connect
I can read it and i can see the good value...
using nRF51-DK
I'm a noob and currently trying to implement a custom service by modifying the 'Heart Rate Service' example which inclued the 'BAS' which is battery status...
Hello All,
I am working on the NRF52810 board with 15.3 sdk in segger IDE.
I have implemented fds with 2 key with 1 file id to store data.
I am storing 2 - 3 1 byte...
Hi, I'm working on building an embedded computer with Bluetooth capabitilites. I am aware of the various WiFi/Bluetooth chips, but my application does not need WiFi, only...
Hi,
We are developing the cycle power services and facing the issues in using the control point characteristic. I am able to connect and observe all the characteristics...
Hi,
we are using MQTT to push the sensor and GPS data with 1 hour interval. After 4 consecutive connect and disconnect, MQTT is returning socket error. It requires the device...
