Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hi, We are working on Thingy91(nRF9160-pca20035). When thingy91 connected to system through USB, We getting BLE UUID values through nRF52840 on nRF9160(on nRF Cloud also)...
Hello,
I am porting a software to the nRF52 SDK16.0 . This software uses Floating Point numbers with Exponent-Byte=0x7F to signal Error conditions (then treated as unsigned...
Hi. I want to evaluate the current consumption of the nrf9160 module (I have a Thingy91) and I want to disable all logging functions. I started with the mqtt_simple example...
I have a characteristic with variable length and max length of
NRF_SDH_BLE_GATT_MAX_MTU_SIZE - 3
i.e. the max possible data length based on the max MTU.
During connection...
My Thingy:91 was added to nRF Cloud using "+" > "LTE Device" and then "Already have an active SIM? Skip this step" (iBASIS roaming doesn't work properly in Switzerland so...
I've been trying to get the MQTT simple sample started however after changing the hostname to "mqtt.eclipse.org" and running the sample, it stops with this error. Please how...
Hello, I am using NRF51822. I want to run UART communication on two different baud rates for 2 different hardware on pin number P09(TX) and P11(RX) respectively. I have to...
The queued writes library provides AUTH and EXECUTE events, but I think it also needs a CANCEL event.
In my code, when I receive an AUTH event I obtain the data buffer using...
Hi,
I got a brand new nRF916 DK. I updated the modem firmware to mfw_nrf9160_1.1.0 and updated the application firmware Asset tracker with nrf9160dk_asset_tracker_nbiot_legacy_pco_2019...
I have set up a PA / LNA and watched the radio details.
When the connection interval was 50ms, it was confirmed that the device was communicating every 50ms.
Look at...
Hello
I want to program and debug NRF52840 dongle using jlink But the jlink is not able to find the target . i am using SEGGER J-Link Commander V6.60d application for flashing...
Hi, Sir:
I am using nrf9160 to develop a project of mqtt and GPS, using mqtt to upload GPS data to the cloud server; I use the software and hardware information as follows...
Hi! We were wondering if the Nordic Thingy 91 has an IP-rating? How resistant is it to humidity and could it be deployed in remote locations such as a forest for a prolonged...
Hello,
I have made my custom application and added that in the SDK example folder and I am able to run the project. But after that when I was cleaning my project I got...
