Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
How to program flash with the output HEX file and SoftDevice file using NRF52-DK.
When programming with the output HEX file the device does not work, I need also HEX - SoftDevice...
I'm trying to set up a project with SDK 16.0.0 using FreeRTOS with the softdevice. The device will be battery powered and therefore power management capabilities are required...
Hi all,
I am trying to generally gain a better understanding of the GPIOTE module and how it can benefit myself in the project I am working on.
I am essentially attempting...
Hello
Does the nRF5280 include Schmitt-trigger inputs on the GPIO pins?
If yes, what are the voltage threasholds for the rising- / falling edges?
(Can't find anything...
Hi,
How does disconnect work in S112?
In the ble_template project, I did not find anything in DISCONNECT event.
static void ble_evt_handler(ble_evt_t const * p_ble_evt...
I have a nrf52833 pca10100 which can connect to nRF Connect Desktop to program fine. EVBW833 should have the same chip DK but it is not being recognized. Is there a way I...
Hi
On my custom board, I have an external flash connected via SPI. . The nrf runs on mfw 1.1.0.
Without activating the flash, I get an average current consumption of around...
Hello,
I am using nRF51 DK and it is programmed with s130 soft device and uart application hex file with nFGo studio.
It programmed successfully but device not showing...
Hi, guys. The codes in Nordic Github like
Android-nRF-Mesh-Library / Android-BLE-Library / etc
are written in Java.
https://medium.com/@nithinjith.p/ble-in-android-kotlin...
Hi,
I'm currently evaluating the nRF9160 chip as a potential replacement device in our internet-connected products. In most cases the zephyr documentation and examples are...
Hi,
I modified your USBD BLE UART Example by commenting out the button and LED code to run on a dongle with J-Link debugger soldered on.
I removed the bootloader and set...
Hi I am new to NRF52832. I am using SDK 16, Multlink Central (ble_app_multilink_central).
Here are my questions:
1) The software keep resetting when I flashed the code...
Setup nRF52840 DK S140 nRF52 SDK v16.0.0 nRF SDK for Mesh v4.0.0 Goal I would like to be able to disable the Mesh stack and all radio operations so that my application can...
Hi,
[Softdevice 6.1.1]
I am developing an application which uses the radio timeslot api in conjunction with BLE. Even without starting BLE advertising, or any other BLE...
I did some evaluation on nrf9160dk recently. I try to run some at command to control lte modem, but some wired thing happen.
After I introduce at command in to one work...
