Draft — ready to post on Nordic DevZone / Zephyr mailing-list
Title nRF5340 DK + MCP2515/TJA1050 module — can_start() always returns -EIO even in loop-back
Hardware...
Hi We are working on setting up CI/CD pipelines for our nRF application. The application is set up as a stand-alone application with its own west workspace. It uses external...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hello, Is it possible to do a save as or copy an example to another directory/folder without having to re-link all the .c files? I am using SES 4.30c. Every time I take an...
I am developing based on 52840. I can only supply VDD at 2V. I wonder if that is doable. If the answer is yes, then how should the VDDH be connected?
The datasheet requires...
I have custom board with nrf 52832. I am using SDK 15.2.0 and softdevice s132 V6.1.0 to transmit advertising packets periodically. I have written simple application that reads...
We use nRF52840 chipset to design a BT module, and it went into pre-production now. But we found the RX sensitivity is not good. We need your help to confirm the RX sensitivity...
So I am using nRF52811 and I have noticed the battery voltage going at a constant rate and suddenly for a time of 2 mins the Voltage value (ADC) dips and it comes back to...
Hi,
I read many post on devzone, but still not familiar with programming "custom board" in my case, board from Sparkfun. My Sparkfun is correctly connected to nRF52832 DK...
Hello,
I am working to replace my BM70 with nRF52 series. So it has to be quick and simple solution. So, I used nRF52840 USB dongle as my slave (Peripheral Example code...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
Is there a way to know the cause of the reset?
I connect the PC to the device and run it in debug mode. However, nothing is written...
I'm running SDK 15.3 with SD 132 and SES 4.30.
I am working with the ble_app_uart_c as the base code and adding other functions. I've gone through the app_timer tutorial...
Hey guys,
I'm working with a Laird BL652-DVK (nrF 52832 - Chip) and Nordic SDK v.14.2.0. Now I try the SPI example and I don't know which register is adressed in the last...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image.
This issue is similar to below ticket with -eraseall and chiperase...
Hello,
Im configuring ADC on 3 channels. However during debugging when I stop Keil I see that in all channels the acquisition pin is the same AIN1.
Any idea why is this...
Hello, I found an examples using ble_app_uart and and MPU6050 from different SDK's. I am trying to update the to SDK16 and have got it to build successfully but when I try...
