I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
Hi All,
I have to implement an I2C Slave on my nrf52833 BLE project which is currently working (SDK 2.9.2)
I need some confirmation with the following step:
I have...
I am using the 54l10 chip, and after compiling the project, I will receive a hex firmware and a zip update package. The bin firmware and hex firmware in this update package...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
Hello,
I am struggling to solve 2 problems ,
1st :
I have 4 AAA cells (2 in series each ) to make a good power source !
The Problem :
I have to measure the battery...
Hello,
In the past few months I have tried to develop with the nRF52810 with Keil and SDK5 (15.3.0). The biggest problem I am having is that many example projects have errors...
Hi,
When evaluated under the following conditions, there was a temperature dependence (See the following Results ).
How mach temperature dependence of TX power?
Does...
I have looked at some other NRF_ERROR_BUSY questions and the answers seem to be very dependent upon the situation and not necessarily 'busy' in the usual context of busy....
I am using SDK 16, SoftDevice S140 V7.0.1 for nrf52840.
I am using the following settings,
and in scan_init()
Up till here the m_scan has the name saved to be filtered...
Hi, I'm trying to get nRF Connect 3.2.0 running (connecting to a nRF52 DK with a PCA10040) and keep getting a 'CouldNotLoadDLL' when starting the BLE app. I'm using Ubuntu...
Dear All,
I am trying to learn how to program via Embedded Studio by using the smaple code in ble_app_blinky_pca10056e_S112 file.
When I open the file via Embedded Studio...
I'm trying to make a "simple" change to the asset_tracker project so that it will send the reporting data to my own server instead of the nRF cloud. However, I am unable to...
Theranica current solution already has a printed MIFA antenna and an impedance matching circuit that they have tested and is working very well.
they would like to keep using...
Hello,
One of the devices I have could not connect to AWS cloud. While checking if the credentials exist, I got the following error :
NRF_KEY_MGMT_CRED_TYPE_CA_CHAIN err...
Hi.
I'm trying to use nrf52832 twis as twi slave.
nrf52 DK(pca10040) is TWI slave (data receiver) arduino uno is TWI master (data transfer)
My code. (examples/peripheral...
Hello,
When I include in my code (Arduino IDE) sd_power_dcdc_mode_set(NRF_POWER_DCDC_ENABLE) on E-Byte 52840 module (E73-2G4M08S1C) power consumption increases to 30mA instead...
Hello,
Can the new nrf21540 extend the range of a nrf52840 in long range mode?
Late 2018 I developed equipment using the nrf52840 in Long Range Mode.
In some use cases...
Hello,
I'm new to nRF devices. I wanted to learn some basics with my nRF51 dongle.
But to my surprise the only free supported IDE is Segger and there is no clear step...
