Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have designed a custom board based on nRF5340. Now I am trying to do flashing and RF testing of it through nRF5340 development board but can't even flash it because...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
We are developing a product that will have a wireless and wired option, based on the NRF52840
The strategy is to release the wired option first, followed by the wireless...
Hi Dev Team,
Please guide me that, What is the data format needs to follow between BLE profile and iPad in order to transfer data.
I am performing both update(read) and...
Hi,
We have an extra current of 1uA while in system off mode(no RAMS). we get ~1.6uA instead of 0.6uA as we read on SPEC.
Do you have an idea what may cause the extra 1uA...
I am trying to modify the ble_app_hrs so that i can write a value to the board and save it as a new heart rate value. So far i have added a BLE_GATTS_EVT_WRITE case to the...
Hi,
I tried my best to solve my problem via forum but unfortunately no success.
I got nrf51 DK and played with it a lot. successfully program the samples and tweak them...
Per release notes, flash memory footprint has changed. The Multilink central project resets when trying to clear pstorage memory area and so I'm assuming that it is protected...
Hi,
Since i don't have nrf6310 board, i tried to test the multilink central application with pca10001 board, after referring the nRF51 SDK document. But unfortunately it...
Folks,
I've designed and implemented two product prototypes using the QFN package for the nRF51822. Now I need to move to the BGA version to shrink the designs. The nRF51822...
Im using the nRF51822 board with the nrfGo motherboard. I noticed the atmel microcontroler on the motherboard supports USB otg. It is possible for the nRF51822 to use the...
Hello,
I just received my nrf51822-mkit. I would like to connect it to android, but I need the product keys. I cannot find the product keys on the PCB or in the packaging...
Only p0.00 to p0.03 event can trigger an interupt in nrf 51822?
By nRF51 Series Reference Manual v1.0 ,I find that it only have CONFIG[n] (n=0..3) in GPIOTE, does it means...
Hello.
I use nrf51822 EK and TN-901 temp sensor.
My plan is nrf51822 slave, TN-901 is master
or considering the roles reverse.
Getting value is spi and output is uart...
s120 1.0.0.1-alpha loads fine
s120 1.0.0.2-alpha won't load - The given hex file did not load successfully
s120 1.0.0.3-alpha won't load - same error message
See attached...
Folks,
Prototyping a wearable device using the nRF51822, so we're talking about Bluetooth LE and the 2.4 GHz band (although the protocol probably doesn't matter). Since...
