Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hello,
We are designing a custom board, and we would like to use an external crystal for the low frequency clock source, but we are running into disconnect issues. A similar...
Hi,
I have been trying to get the BLE secure DFU example working on a custom board (nrf52840 - BC840 module). I tried it on SDK 15 and SDK 16. When I flash the BLE DFU,...
I am trying to get the current time and the current time zone. I see there is some modem commands LWM2M commands that appear to have the capability to do that. When I try...
Dear all,
I have an application that requires me to keep advertising until the button is pressed.
I use a timer to read the status of the input pin and then if input is...
All of our initial BLE project development has been done using a the Nordic nRF5_SDK_15.3.0_59ac345 SDK and 10056 eval board. Now we have a production board that is based...
Hi All,
I am developing an application with a custom BLE profile, one in which i would like to notify the central of certain values as soon as they connect. I have built...
Dear Devzone team,
What is the fasted way to fetch and store the Thingy91 measurement and device data outside of the nrf Cloud? If i just deploy the AWS certificates will...
Hello,
We are currently working on a project where up to 40 battery powered devices need to talk with one router/coordinator. Each device features a proximity sensor and...
The instructions do not tally with https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v12.2.0%2Flib_crypto.html&cp=4_0_1_3_9_2&anchor=lib_crypto_installing...
Hello everybody,
I tried to send data while in scanning mode (RX 100%).
I don't get any error when sending but data seems not to be sent (not shown in ANTWARE).
Is what...
Hi
So, Im trying to repeat the ble_central_and_peripheral example but with my own services. To be easier let's call the service " snsr ". So, I did the snsr.c and the snsr_c...
We have a situation where a device might have a sim card field installed, and sometimes, depending on the vendor, the APN settings might need to get changed.
Is there a...
Hi! We're using SDK 16, trying to implement OTA DFU functionality on our NRF52840 device with SD S113. Previously, SD S140 was used on our boards, and so when getting the...
Hi All,
We met a problem when we update the DTM SDK.
The conditions:
1. Same hardware
2. Use official nRF52832 Development board.
A. Old DTM SDK
SDK version...