Hi,
1.How to modify the transmission power of the example direct_test_mode to 4dBm? 2. Please provide Method 1 and modify it using the CONFIG configuration? 3. Please provide...
Previously, I designed a PCB for the nRF52832 chip using the RFANT3216120A5T antenna ( link ). However, I was only able to achieve a very limited Bluetooth range of around...
Hi, I'm relatively new to Nordic microcontrollers and have recently completed the beginner's course. Sorry in advance if I made an obvious mistake.
I am currently trying...
We are running a nrf54l15 board that uses an NFC T2T tag to encode a URI to open an application. We have noticed that sometimes, the current stays higher (~200 uA) after the...
I’ve got a bit of a hardware issue with the nRF52811 UART, receiving DMX data from a Chinese DMX controller.
Standard DMX data-rate is 250Kb/S, so the minimum bit time is...
Hi,
I am using the Nordic UART Service (NUS) peripheral and central on two nRF52840 DKs and I am developing with nRF Connect SDK v3.0.0 .
I can't manage to increase the...
I am getting an occasional softdevice assert on a BLE central device (hub). Both the central and peripheral devices are nRF52840 using Coded PHY and NCS v2.7.0. This error...
Hello All,
Please share me the link where I can get complete explanation on software part for how to use following wakeup options as stated in datasheet
1]The detect signal...
Hi all,
I have 3 nRF52840 Bluetooth tags and I have used Segger Embedded Studio for programming the nRF52840 for the proximity application. Once I have programmed all the...
Hi,
We are seeing some strange stuff when trying to pass floating point values to a function. When we pass the parameter by value (meaning as an actual floating point number...
Hi!
I'm trying to communicate with modem through UART.
Power supply: Battery connected to VDDH
VDD_nRF: 1.8V
nRF52840 DK connected to modem devkit using wires (about...
I am using example code TWI_sensor. It is the same code i just switch ports and added couple of lines that would power up my sensor. After running it i can't even clk going...
Dear Community;
I am using this code provided by a Nordic engineer to make some HTTP request in order to use Telegram Bot API . It works fine but after 1-2 days working...
Hi,
I am in search of an SoC capable of processing data and having Bluetooth features. I have to use it in an automotive design and need to be compatible for the application...
Hi, I am having an issues when i run the command
west init -m https://github.com/NordicPlayground/fw-nrfconnect-nrf This is the response : I found a similar issue here but...
I'm trying to find documentation about the RADIO peripheral of the NRF51822 chip. In the NRF SDK file nrf51.h i can find all the registers like 'PCNF0' and 'CRCCNF' but there...
Trying to setup nRF Sniffer v2.1 for nRF52 Development Kit (PCA10040)
1) Wireshark does not see the Sniffer. When I run nrf_sniffer.bat, I get this:
C:\Program Files\Wireshark...
Hi,
I am now trying to reduce the total number of packets during the dfu process. After reading all the code about dfu in both app and bootloader, I find that in this process...
I am trying to install the pc-ble-driver onto my PC so that I can get the dll and lib files necessary to read/write from a nRF52840 Dongle programmatically. I am following...
Hello, we are using microchip bluetooth as uart tranpsarent and we have custom app in android to control it. In future we are going to do mesh application in android. But...
Hi
Using SDK for Mesh 4.0.0
I had a strange behaviour: Setting up a model with publication period 16s resulted to an interval of actually 10s. Multiples of 10s were working...
Two traces are attached performing the same function. A connection is made to a bonded device. The peripheral times out and the central tries to reconnect. with SDK 14/SD5...
