Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
I use the SPIM to access a nand flash memory device. There are times, when I need to "free" the SPI bus allocated by the nRF52840, so that another CPU can access the memory...
I have been closely following this thread ( https://devzone.nordicsemi.com/f/nordic-q-a/52689/nrf9160-lte-sensor-gateway-on-thingy-91/217018 ) to provide support for the LTE...
Hello all,
I am using the NRF52810 board with SDK 14.2
I wanted to convert pca10040 to pca10040e file of buttonless dfu and secure bootloader .
I have gone through this...
Hi, I can read data with my laptop BLE as below.
Could anyone tell me where can I find the data layout doc? I want to figure out the data layout and dimension.
Thanks...
I've been having several issues with the nRF52840 so far:
Issue 1:
When trying to flash an nRF52840 with NCP firmware using a Segger JLink, I connected the SWDIO and...
Hi all,
I noticed an issue on the last release of the NRF Connect mobile app at least on Adroid devices.
It seems that every time I am trying to make a secure DFU (buttonless...
Hey everyone!
How often does PM write into FDS? On each connection? Or on each new bonding? PM has some kind of peer ranking so I suppose that it needs to write on each...
Hi Nordic Forum! I'm currently developing a CLI controlled BLE scanner using the nRF52840 Dongle. Essentially I brought over the CLI example and adapted it to the a central...
Hi
it looks like the Publication Retransmit Count and Interval states default to 1 time and 100ms respectively. Is there a reason these defaults apply? I don't think it...
My thingy:91 does not connect to the LTE network. However it does detect the Swisscom network (Switzerland) and shows it as available. After a few minutes it sometimes changes...
I would like to program the 52840 with the HCI_UART sample to use it for Bluetooth scanning. I did this and lost the USB serial out. I now understand that on the Thingy91...
Hello,
I am evaluating the nRF52840-DK. I just want to play around with Nordic for awhile to determine if I want to port my current project which is written in C++ for Teensy...
I want to run various applications in some cases
what I want is :
In general, it runs own application.
When external memory(SD card, USB, EEPROM, etc... something...
Hello All,
I have developed advertising init in 14.2 sdk (in segger ide).
(working on nrf52810 board)
I wanted to migrate same functionality to 15.3 sdk so how i can...
