Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I'm attempting to synchronize/correlate measurements made by two separate nRF9160 devices and was hoping to use a timestamp to do so. Essentially I would like to measure the...
I am using GPIO interrupt event.
And I added the following code because I wanted to observe PA / LNA.
Adding this code stopped the GPIO interrupts.　Can the two coexist...
Hi,
For nRF82540 dev board, the secure bootloader code has embedded many NRF_LOG_DEBUG(...). But they are not displayed or output to virtual COM port. Is there anyway to...
Hi all,
I'm looking to develop a proprietary start network that may support around 30 devices, with very low bandwidth (pretty much just a keep alive and a sensor state...
I just came upon a blog post from ARM about the use of the Cortex-M4's FPU:
https://community.arm.com/developer/ip-products/processors/b/processors-ip-blog/posts/10-useful...
Hi, I am looking for sample code that can reconnect to bonded devices and share the encryption keys with DFU-OTA.
I have worked using DFU-OTA (JUST_WORKS option); I question...
hi all,
i can't update new nrf cloud certificate
"There was an error generating the certificate: No Nordic product with device id nrf-xxxx...(imei)and ownershipCode...
Hi.
I have a Thingy91 that I will use as a remote wake up for another system. I am trying to estimate how long the system will be able to run on a single charge with the...
Hi!
I am trying to find an example project for the Rigado BMD-340 eval board, or some guide to getting running with this board. We are working on a new product using BLE...
Hello,
I am using peer manager to handle security and bonding. Everythin works fine (bonding witth MITM).
However, when a known peer connects, I am getting 6 (six) PM_EVT_PEER_DATA_UPDATE_SUCCEEDED...
I want to make The Thingy91 a bluetooth peripheral device . I want it to send the generated temperature data to cloud or another device. How do I do this? I had problems with...
Hi Nordic Team,
Please share logic to scan specific peripheral devices which are advertising with a filter other than filter for device name, uuid, short name and MAC address...
Hi,
I am using nRF52832 with SDK v16 with s112 BLE stack.
I am trying to enable the DIS service like below:
The device can boot successfully but when I checked the...
Hello,
I want the scanner to receive both AUX_ADV_IND PDU event and AUX_SCAN_RSP PDU event for the case when AUX_SCAN_RSP PDU will be lost I still want to have AUX_ADV_IND...
Hi,
I am using RTT log with nRF52832, my question is when debug port is disconnected, what will happen to RTT logger?
Will they be simply ignored? or will the debug pins...
