Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I am using nRF52832 DK.
I am trying to print Battery service value in log file ( Client side ).
So where i get this information and how can i print this information in...
I’m looking for setting up an evaluation network considering of 10-14 nodes as data sources that are to send data values on a periodical basis to a data sink mode that will...
Hi everyone,
I am developing application on nRF52832 using SDK 15.3 on SES, windows. I am using secure DFU bootloader for FOTA process.
Scenario 1 : If I don't use DFU...
Hi Team,
After I add the ANT module into my project, I found the fds_gc() will always return error 1( NRF_ERROR_TIMEOUT ) when it has dirty records. If there are no dirty...
Hi,
I am using NRF51822 SDK12; S130 and trying to qualify Batter level service, So far encountred a problem with Test Case: BAS/SR/DES/BV-02-C, the Verdict is INCONCE all...
Hello, I just got the nRF52832 development board and i was playing around with the examples. I was able to connect it with the nRF Connect app on my mobile and desktop. But...
Central info SDK: 15.3 nRF52840
Peripheral info SDK: 13.1 nRF52832
I want to increase the communication speed after connection. I want to know how to set the communication...
Hi,
I'm trying to measure the power consumption of the nRF52840 chip , which runs the "nimble" BLE stack rather than SoftDevice.
However, the nimble BLE stack runs on...
Dear Nordic Team,
We want to use the FreeRTOS for commercial use, kindly request to answer the below questions.
1. Is AWS FreeRTOS open source & commercially distributed...
Hey all, I'm a beginner to bluetooth,
I ordered the NRF51822 dev kit and it worked easily out of box with my android phone.
I'm creating my own android app to communicate...
Hi Nordic
I want to change mesh-sdk-4.0 LPN example tx output power to 4dbm, including proxy broadcast, mesh packet,
I try to change " RADIO_POWER_NRF_0DBM " in whole...
The Nordic Uart service for peripheral devices has a function ble_nus_init() which takes a callback function in a struct.. Later on this callback function may be called with...
I am doing the project using nrf blinky.
My phone cannot find the nrf52840 . Before this it is ok, but now it cannot discover it . I notice that LED05 is blinking very fast...
Hi guys ,
I am trying to connect thermistor with the ADC pins of nRF.
I use the steinhart formula to calculate the temperature in degree celcius. I used a voltage divider...
