I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hello,
I have tested and verified the code for my application on the NRF52 DK, but now I need to program my own custom device using the nRF52832 chip. I saw there was a...
Some bugs in ble_app_hrs_freertos example from the SDK when handling buttons: (at the end of this listing are same tests but with ble_app_hrs (no rtos) and buttons are handled...
Hi, We are working on Thingy91(nRF9160-pca20035). When thingy91 connected to system through USB, We getting BLE UUID values through nRF52840 on nRF9160(on nRF Cloud also)...
Hello,
I am porting a software to the nRF52 SDK16.0 . This software uses Floating Point numbers with Exponent-Byte=0x7F to signal Error conditions (then treated as unsigned...
Hi. I want to evaluate the current consumption of the nrf9160 module (I have a Thingy91) and I want to disable all logging functions. I started with the mqtt_simple example...
I have a characteristic with variable length and max length of
NRF_SDH_BLE_GATT_MAX_MTU_SIZE - 3
i.e. the max possible data length based on the max MTU.
During connection...
My Thingy:91 was added to nRF Cloud using "+" > "LTE Device" and then "Already have an active SIM? Skip this step" (iBASIS roaming doesn't work properly in Switzerland so...
I've been trying to get the MQTT simple sample started however after changing the hostname to "mqtt.eclipse.org" and running the sample, it stops with this error. Please how...
Hello, I am using NRF51822. I want to run UART communication on two different baud rates for 2 different hardware on pin number P09(TX) and P11(RX) respectively. I have to...
The queued writes library provides AUTH and EXECUTE events, but I think it also needs a CANCEL event.
In my code, when I receive an AUTH event I obtain the data buffer using...
Hi,
I got a brand new nRF916 DK. I updated the modem firmware to mfw_nrf9160_1.1.0 and updated the application firmware Asset tracker with nrf9160dk_asset_tracker_nbiot_legacy_pco_2019...
I have set up a PA / LNA and watched the radio details.
When the connection interval was 50ms, it was confirmed that the device was communicating every 50ms.
Look at...
Hello
I want to program and debug NRF52840 dongle using jlink But the jlink is not able to find the target . i am using SEGGER J-Link Commander V6.60d application for flashing...
