I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Hello all,
I have a pretty simple question that I hope can be answered for me. I'm integrating an nrf52832 development kit (PCA10040) BLE sniffer into a test fixture to...
hi,
i able to write and read unsigned integer value from the flash, but when i try to write some string to it ,the device is not responding.
void Reading_the_data_from_flash...
Hello Sir,
I would like to ask about the handling of the interruption in the nRF52 SDK.
The versions for SDK and SoftDevice are 15.3.0 and S132 v6.1.1
In the processing...
Hi all,
I am using a nRF52840 with SDK v16.0 on SES. I am trying to understand the flow of code in the secure Booloader(/SDK_v16\examples\dfu\secure_bootloader\pca10056_s140_ble...
Hi ,
I am trying to interface sg90 toy servo with NRF52840 , I am using nrf library but dont know how to drive it from 0 degree to 90 degree to 180 degree . May I know the...
Hi
I m using NRF52832 for beacon application.In my application, the device should be in the system off mode .After holding button for 5 secs, the system will back to idle...
Hi
I'm using SDK version15.2 and SD on a custom board based on nRF52840.
The board has two serial ports, and I want to use both independently. Using the Serial Port Library...
Hi Nordic Team,
My requirement is-
Advertise -> Connect to 1 device -> Send packet -> Disconnect -> Delay(1min) -> Advertise -> Connect to 2 device...
I am using Timer...
I am using nrfMeshProvision cocoapod to create a Mesh Network using a iOS Mobile application. In first step of identifying the device, i am able to call bearer.open() and...
Hi,
I've used the nRF connect 'Getting Started' software and tutorial to setup a development environment, however i am having problems with the "Set up a project in SEGGER...
Hi Nordic Team,
Please share a logic to filter with address for connection over BLE. Please help as soon as possible.
Thanks & Regards,
Aswati Vijaykumar
Hi
I am currently developing a demo application and started with the ble_app_template project from the ble_peripheral_folder (s140 softdevice, sdk 16.0). I copied it to...
I am using a module called Core51822 which includes NRF51822, with the NRF51822 Evaluation kit and the ST Link to program it from Arduino IDE.
I want basically to program...
can someone suggest me some tutorials how to do programming in nrf52840 from scratch.
i have tried some examples like blink an led just like opening the file and running...
