Hello,
I'm starting a new nRF51 project on mbed for a custom board. I wish to know what is the "cleanest" way to define pinout (what file to edit) ?
Thank you
I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Hi,
I am working on Bluetooth peripheral and pin_interrupt_change program in nrf51422 on sdk 12.3 .
so I added pin_interrupt_change program in the ble_app_uart program...
I'm attempting to synchronize/correlate measurements made by two separate nRF9160 devices and was hoping to use a timestamp to do so. Essentially I would like to measure the...
I am using GPIO interrupt event.
And I added the following code because I wanted to observe PA / LNA.
Adding this code stopped the GPIO interrupts. Can the two coexist...
Hi,
For nRF82540 dev board, the secure bootloader code has embedded many NRF_LOG_DEBUG(...). But they are not displayed or output to virtual COM port. Is there anyway to...
Hi all,
I'm looking to develop a proprietary start network that may support around 30 devices, with very low bandwidth (pretty much just a keep alive and a sensor state...
I just came upon a blog post from ARM about the use of the Cortex-M4's FPU:
https://community.arm.com/developer/ip-products/processors/b/processors-ip-blog/posts/10-useful...
Hi, I am looking for sample code that can reconnect to bonded devices and share the encryption keys with DFU-OTA.
I have worked using DFU-OTA (JUST_WORKS option); I question...
hi all,
i can't update new nrf cloud certificate
"There was an error generating the certificate: No Nordic product with device id nrf-xxxx...(imei)and ownershipCode...
Hi.
I have a Thingy91 that I will use as a remote wake up for another system. I am trying to estimate how long the system will be able to run on a single charge with the...
Hi!
I am trying to find an example project for the Rigado BMD-340 eval board, or some guide to getting running with this board. We are working on a new product using BLE...
Hello,
I am using peer manager to handle security and bonding. Everythin works fine (bonding witth MITM).
However, when a known peer connects, I am getting 6 (six) PM_EVT_PEER_DATA_UPDATE_SUCCEEDED...
I want to make The Thingy91 a bluetooth peripheral device . I want it to send the generated temperature data to cloud or another device. How do I do this? I had problems with...
Hi Nordic Team,
Please share logic to scan specific peripheral devices which are advertising with a filter other than filter for device name, uuid, short name and MAC address...
Hi,
I am using nRF52832 with SDK v16 with s112 BLE stack.
I am trying to enable the DIS service like below:
The device can boot successfully but when I checked the...
Hello,
I want the scanner to receive both AUX_ADV_IND PDU event and AUX_SCAN_RSP PDU event for the case when AUX_SCAN_RSP PDU will be lost I still want to have AUX_ADV_IND...
