Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
I am considering using a high-Q BAW filter to drive as near the band edges as possible and roll-off noise beyond.
Source of my interest:
https://www.qorvo.com/design-hub...
I am using nrf52832 SDK14.2 development, now the system will generate some strange exceptions, I am worried about the stack overflow, is there any way to confirm whether the...
Hi All
We are using nRF9160DK and want to send data to the cloud (Adafruit or Thingspeak) using MQTT protocol but we do not have NB-IoT
Network in Our area so it's possible...
To the kind attention of Nordic support team,
I've been reading in this post:
https://devzone.nordicsemi.com/f/nordic-q-a/44042/using-nrf52810-with-gzll_nrf52_arm-lib...
Hello,
I need to validate my selection for crystals working with the NRF52840. For the 32.765kHz crystal I have chosen the 9HT12-32.768KBZC-T from TXC Corporation. For the...
i have test with RTC using nrf_calender.c.
It will prints output data on terminal window.
But, I didn't recognize the actual data.
Output data is mentioned below,
...
I am attempting to use libmbedcrypto.a from the Thread/Zigbee SDK version 3.2.0. I am linking it from:
external/openthread/lib/nrf52840/gcc/libmbedcrypto.a
and yet...
HI,
I want to implement the software security to NRF52832 such a that no one should be able to read the memory or tap the data during Bluetooth communication.
Regards...
Hi,
I am trying to interface tlv493d with nrf52 dev board.
I have taken driver code from infeneon
https://www.infineon.com/cms/en/product/evaluation-boards/tlv493d-a1b6...
Hi
I face ble disconnection issue.
we use external crystal 32.768khz. However, when I check it , the load cap is wrong. It should be about 9pF but it is 1pf.
The frequency...
Hi,
When factory resetting the flash storage, I delete all records, and then call fds_gc(). However, the page that's used for garbage collection still contains a copy of...
Invitation : The provisioner invites the unprovisioned device to send its provisioning capabilities information.
Firmware version from this examle: https://github.com...
Hi.
I've bought the nRF52833 DK and I want to use it with Mbed OS.
But I'm not getting it to work. If I compile the "mbed-os-example-blinky" program for target nRF52-DK...
Hello.
I would like to ask about writing data from Smartphone to Thingy. How to change characteristic using setOnCheckedChangeListener.
Is it correct way to change characteristics...
Dear people ,
nRF52840 and 15.2 version
I have uploaded the program ble_app_hts in my NRF52840. After which I uploaded ble_app_uart but I still get the "Nordic_HTS"...
