i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Hello I have a custom board with LR1110 Lora radio I'm getting errors that driver is not supported when I define the spi1 for it
lora0: lora @ 0 {
compatible = "semtech...
I am looking for a solution where I can set custom and configurable root Kconfig file via Cmake cache variable, which can be specified through the west build command.
Steps...
Hi,
1.How to determine whether the nRF54L15 LFRC has been calibrated? 2. What logs can show the calibration completion event? 3. Or, apart from logs, what other methods...
Context:
VS Code
NCS 2.9
nRF54l15 custom board
Mac OS Sequoia15.5
peripheral_lbs sample project
Goal:
The goal of this project is to create a bluetooth beacon...
We are working on a prototype of nrf9151 with various sensors and nrf54L15. Our schematics designer says U13 (TCK106AG) may not be needed. Please let us know its use. regards...
Hello,
I am new to nRF development. I am going through the nRF Connect SDK Fundamentals course.
I wanted to configure a GPIO on the nRF52833 DK board as an output and...
Hi，the Nordic team
I use the SED device by system on mode.I found that my static average power consumption increased by more than 20 ua after I defined an IO port to use...
Hello, I'm running an example of channel sounding using nRF54L15.
The build is fine, but the following error occurs during flash.
Python is using 3.12.4 version. As you...
Dear Team,
I have recently acquired NRF54L15 Development Board for evaluation and from Day 1 experiencing issues with BLE.
I am running simple Zephyr-based BLE Peripheral...
Hello everyone,
I am a EE student and this problem came up during my first big project in zephyr. I'm trying to connect a pwm peripheral (pwm1) to the timer 2 hardware timer...
Hello everyone,
I have an nRF5340 microcontroller (NORA B106 module), and I want to connect a square wave signal to one of its pins to read its frequency or count the number...
Greetings,
I have previously added the LittleFS to the internal flash of the nRF52840 with success using the available documentation. Our .dts & and code is shown below...
We are trying to add CarbonDioxideConcentration cluster in matter. we are able to add temperature and humidity clusters and values which are updated are getting read in chip...
Dear all,
I am wondering, what is the reason for C13 being 3.9pF for QFN package, while there is no capacitor on WLCSP reference design? Could we use like 10nF instead?...
