After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I want to drive a WS2813 led strip using a NRF52810, as NRF52810 does not have I2S, is there any other way to drive the strips. Do you know if there is any library for doing...
Hi,
I am using nRF52832. The chip is connected by SPI with main board on which Nuttx is running.I am developing code to download file from external device using blue-tooth...
Hi
Good day!
We are working on the BQ24715 Digital Charge controller IC and it has got an SMBus communication port and tried to set up communication using the nRF52832...
I am not able to bond with the thingy52 after connection with nRFconnect android app. Because of which I am not able to reconnect to the device. My main aim is to reconnect...
Greetings!
This is about the errata published by Nordic, i.e., software workarounds from Nordic for a given hardware revision.
Example: nRF52840 Errata
https://infocenter...
I have created a customized android app which hosts a form like structure of a patient arriving in hspital. I wish to send these data to nrf52840 dongle which inturn stores...
As the website of nordic shows, I download all the softwares and drivers to build a bluetooth network based on mesh nodes. However, when I open the nRF Connect, I can't select...
I am working on nrf52840 and also the dongle by segger. My data is transmitted via BLE sucessfully but I can only see the results in figure but I can't save and process the...
Hello everybody,
I have programmed the example light_switch (server) and (client) from SDK for Mesh examples on two nrf52840 dongle and it worked .. I can control the LED...
Hello,
I'm currently trying to implement a setup of BLE devices (nRF52 DK and nRF52840 DK) which is potentially secure against the KNOB attack (and also other attacks) and...
Hi, I am looking to use the nrf power profiler to analyse power consumption with some configurations on the NRF52833.
I currently have the dev board PCA10100 and the power...
I was looking for more information about hardware accelerated AES128 functions in the nRF9160. We want to encrypt and decrypt data using this and was wondering if there are...
Hello,
I am currently working on adding the pairing part to the ble_app_uart with peer manager. I have followed the way that is used for ble_app_gls and ble_app_hrs. I could...
Hi support team,
I download mesh (nrf5_SDK_for_Mesh_v3.2.0) serial example FW to nRF52840 DK,
and connect to embedded linux gateway over USB,
I can run PyACI example...
Hi,
It seems that s112 soft device uses IRQ level 0,1,4 of nRF52832.
By default my counter has default IRQ level 6, my concern is about the delay of COMPARE interrupt...
