When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
In the SDK it suggests we use those new nrfx drivers, and says the legacy will no longer supported in the future. However, in the examples of the SDK, it uses the legacy driver...
hi
i am using sdk for mesh v3.1.0 i get my data from the uart and sending it over the mesh. i have been getting an error within the function net_state_seqnum_alloc() that...
Using SDK nrf52_sdk_16.0.0 PCA10040 S132
My code can read and write Flash using the "Data Storage Flash" interface, IE calling fds_record_write(...) and waiting for events...
Hello I am quite new to the hardware encryption topic and I have the following questions.
On a device where the MCU samples a sensor data and stores it to a external IC...
Hi .. I've a Chinese watch with NRF52832 CPU DTNO.1 F18. I'd like to change it watch face as all watch with Mediatek CPU ..
Is there an application to easily do that How...
I have a BLE application that I successfully program onto the dongle by pushing the reset button on the dongle and using the "programmer" application from nRF Connect.
The...
To demonstrate installing the tools for my client I'm going through the process first, on a fresh machine.
Installed SES & invoked it. Got a free license & installed it...
I have a new nrf 9160 DFK. I followed up the instructions from 'Getting Started Assistant' from the 'nRF Connect for Desktop' app. I was able to setup and build the asset...
Hi,
Our company use nrf24L01+ for many years,the maximum output power of 24L01+ always about 0dbm in our application.But recently we meet a problem that the 24l01+ output...
Hello, as mentioned in subject, I have done DFU on nrf51 DK. it is tottaly working fine. As soon as I try to work with Nrf51822 QFAC custom board. It goes in to bootloader...
Hi,
I intend to use the nRF9160 as an LTE module. I will send data to be transmitted to the nRF9160 and receive data from the nRF9160 via SPI. I have read in numerous places...
I just want timer2 to run at 1Mhz so I can grab a microsecond counter as a timestamp. I don't care that it'll overflow after 32 bits. Put together what I thought should be...
Hello, I'm using the Radio Test software (SDK 15.2) to control the N52840 radio IC. Our circuit design requires the use of an external RF amplifier IC. Our software puts the...
Hi everyone,
I am stuck with an apparently simple problem which I am not able to fix.....
I have an SPI device connected to a custom NRF52840 board. I am using NRFX_SPIM...
