When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi, I have nRF9160DK and Thingy:91. I want to store APN configurations in the modem but I can't save the APN. Currently, I am giving the APN information manually every time...
Hi
I have nrf82540 dev boards. I loaded one board with Proximity example (SDk Version: nRF5_SDK_15.3.0).
According to your web page: https://infocenter.nordicsemi.com...
I am working on a project that needs to be a ble central and peripheral. I based my development off the experimental/ble_central_and_peripheral/ble_app_hrs_rcs_relay however...
Dear Sirs, good afternoon
I am working in a design that includes an nRF52840 as main processor.
I need to know if it is possible to have the following peripherals implemented...
Hi,
How do we fuse the debug port on nRF9160? The purpose is to block all access and the ability to erase all from outside.
This is my understanding:
From debugger...
My nrf9160 connects to AWS when using the AWS FOTA example. However, when I start the custom job as setup from the following link:
https://developer.nordicsemi.com/nRF_Connect_SDK...
Hi,
I have a board that emits 0x1818 (Cycling Power) using the nrf51422 chip and firmware using S310 and so forth. Working great :)
Now I just found some strange things...
Hello guys!
We are using nRF9160 SiP module to transfer MQTT messages to AWS IoT. So far, thanks to the cloud_client example and your documentation from here , we were able...
Hello,
I am using Segger Embedded Studio (SES) to develop with the nRF5340 BLE chip. From what I've read, the nRF Connect SDK and Zephyr OS is not tailored for use with...
Hi,
I would like to check my understanding of PSM. Currently, using the AT Client on the local NB-IoT network, I can see that the device is entering PSM after 3 minutes...
Hi, I'm looking for a simple example on how to implement I2C. I've built I2C on my various FPGA's, implemented I2C on various AVR based chips from special function registers...
Good afternoon,
I first devoloped my app based on the nRF52840 (SDK 15.2; S140 V.6.1.0) and it was perfectly working with or without bonds.
After that, and following what...
I've been doing some development on the nRF Mesh platform for the nRF52832 chipset and I'm relying on the Mesh DFU protocol to update my deployed units. Recently I've been...
