Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi,
I have test setup consisting of 2 boards, one that sends a packet every 2 seconds with CTE, and another with a 2-antenna array that generates MagPhase samples and sends...
Hi,
I am using "http_upgrade_ota" project.
I have added UARTE2 , SPIM3 and WDT peripherals in the application.
To use this peripherals i had to make change in "spm...
Hello, I have developed an application that advertises, connects, pairs/bonds using SEC_JUST_WORKS configuration, and then transmits data at ~2 second intervals to a smartphone...
I would like to use NRF Desktop Connect to connect to, and potentially firmware update an nrf52832 via the onboard bluetooth, but the NRF Desktop connect is only available...
Goodmorning,
I developing an application on nrf52840 board with SDK15.2.0 that communicates via BLE with from the APP nordic. I am started from the example project ble_app_cscs...
So I'm trying to implement Mesh OnOff server with BLE DFU supports. My implementation is as follows:
These are my app_config.h and nrf_mesh_config_app.h
I face...
Hello,
I am trying to use several Thingy 52 as peripheral devices, (sensors) connected to a central (Gateway) particle Argon running ( nRF52840). The idea is to connect...
Hi, I have 2 questions regarding multiple controllers using nRF Mesh.
1. I used the import/export option to transfer the network details from Phone 1 to Phone 2. After import...
now I'm on going NRF24LE1 project to low power mode. I try to find several reference as link below, but both of them can't open, someone can help me ?
https://www.nordicsemi...
I have just purchased a nRF52840-DK
I am following the getting started tutorial and when I scan for devices the Nordic_prox device is not appearing in the device list but...
Is it possible to use the NRF cloud outside the dev kits? Working on a custom pcb with custom software and would like to use NRF cloud for it.
---- Christopher
Hi ,
I am working on NRF DFU firmware update. for that i am using secure bootloader code .
I tried with the of way of flasing bootloader code on my custom board and sent...
Hello Nordic community,
I updated latest modem firmware v1.1.0 in nRF9160 custom board. After flashing application code into custom hardware I power off and power on board...
Hello,
I have a question about hardware for Bluetooth LE Audio.
I see Nordic is working on a dev kit:
https://blog.nordicsemi.com/getconnected/le-audio-unveiled-as-the...
HI
I am programming NRF52840 dongle using nrf52840 dk
i have flashed blinky code to my nrf52840 dongle it programmed sucessfully after that i have erased the dongle by...
