I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Thanks in advance for any advice!
We are developing an ultra low powered network. There will be a remote control with numerous buttons. This will connect to 2-10 peripheral...
hai , I would like to program cli uart in pca10059, what are all things to change in openthread stack in order to change UART pin configure and how to compile it ? I use only...
I am trying to implement cli uart in custom board, for which there comes need for me to recompile openthread stack (in order to change UART and LED pin configuration) in GCC...
I was just working with the ble_app_uart example in nrf5_SDK_12.2.0. Minor modification were done to the main function. The build output:
linking...
._build\nrf52832_xxaa...
The site is just showing a product brief PDF, where can I access the full datasheet? Is the crystal oscillator on board or an external connection is required?
Hi,
I am using SDK version 15.3.0. I am trying to implement the ble_dfu example. By default, advertising name is set to "DfuTarg". I want change this to a custom name. How...
I'm using the nrf52840 with connectivity firmware and S140 SoftDevice, accessed through pc-ble-driver version 4.1.1, with NRF_SD_BLE_API=6
Occasionally pc-ble-driver fails...
Hi,
I am trying to find RSSI of the value of the nearest device also I need the Device name, address of those devices. I got the RSSI value but some problem in D evice name...
I'm upgrading a project from SDK 15 to SDK 16. Previously in my gap parameters init I had this code
This works fine for seeing the peripheral and operating it as a UART...
I wasn't sure which product to put in. I am looking for a BLE discovery tool for EEG devices -- particularly the Muse 2 Headband. Which of Nordic's software should I use for...
Hi,
In our project, we are using a small RTOS to switch between simple tasks and set MPU. We would like to run all task in unprivileged mode, but some Nordic SDK libraries...
Hi everyone,
I have written a code that sends data over BLE notifications (IMU data). It works great so far and now I want to read the analog values from eight force sensors...
Hi everyone,
I have a problem I can't sort out. My program runs fine indefinitely if I set one variable in a function at one point but if I don't do that, the program, or...
Hello,
We have around 700 product in the field based on the Simblee BLE module, which was discontinued 1+ year ago. Application was developed using Simblee's proprietary...