I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
Hi all,
I want accive this situation. My peripheral connecting a central with a service for example hrs, then i stop the conect with the function sd_ble_gap_disconnect(m_conn_handle_peripheral...
Hi,
I am using the sample BLE_gls code provided by Nordic.
I have made the following changes in the code:
#define SEC_PARAM_MITM 0
#define SEC_PARAM_IO_CAPABILITIES...
I am using nrf51822 qfaa IC (pca10004 board) with softdevice v8 and sdk9. Now I am trying to do the dfu example. I uploaded the softdevice with the help of nrf gostudio. But...
Hi,
Please correct me if I'm wrong.
Consider an application that will read 6 bytes of data from I2C at 200Hz (each 5mSec) and will stop after 2000 reads. This will be...
Hi,
Apologies if this is an obvious question, but I haven't been able to establish from previous questions or the data sheet whether it is necessary to use an external...
I'd like to be able to change the connection interval from my central device on the fly after a BLE connection has been established between it and the peripheral. What's the...
Hi,
In the ble_app_proximity project in SDK 0.9.2, I was trying to add manufacturer data to the beacon. Here are some of the code snippets which I changed in main.c
#define...
Hello,
I am working on S120 stack with 9.0 SDK and testing with heartrate application and iPad as a peripheral. I am getting the central device as nRF51822 after central...
Do I need to implement my own timer to wrap this function? I appears that I might receive a BLE_GAP_EVT_TIMEOUT timeout event but testing has yet to reveal one.
My test...
Is there an example that is a minimal example of advertising on S110?
It might even serve one attribute that is set to a constant like '1234'.
This would help me bring...
HI
I am trying to use mkit as programmer by P20
FOR third part BLE brd
VDD---mkit.vdd
GND--mkit.gnd
SWD--P20.4
SWC--P20.5
bisides, for
P20.3(SH_VTG) connected...
We're going to be programming and debugging our prototype nRF51822 board using this adapter from Segger. It's the same connector as comes with the J-Link LITE in the dev kit...
Dear Nordic Team,
I am using Nordic DK board,
Now i want integrate UART to hid-mouse application. So that whatever data i can receive , will send to HID device without...
Hello everybody,
I'm trying to use pstorage module but it seems that the example_cb_handler function is never called when I try to store data.
I noticed similar issues...
There have been a number of other older topics with this same error message symptom, but I've tried all the solutions proposed and none have worked to solve this specific...