There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hello,
I'm here again because this time I need to autoconfigure (configuring from inside program, no use of any nrf app) heartbeat destination node and source node.
For...
Hi,
We are currently CE certifying our product, and the test lab requires a fixed frequency firmware for the device. Are there any generic samples for this within nRF Connect...
There is a possible typo in the nRF5340 DK documentation.
https://docs.nordicsemi.com/bundle/ug_nrf5340_dk/page/UG/dk/ext_programming_support_P20.html
In the top picture...
Hi, We developed our custom BLE electronic board based on the nRF54L15 SoC. On this project the nRF54L15 firmware setup a SPI slave interface in order to receive commands...
Are there any good tools/apps to commission/provision an ble mesh application that is NLC compliant. Silvair is a great option, but is a closed ecosystem. We are looking for...
We are using the nRF5340 and our use case makes full use of all 4 shared peripherals for SPI and TWI as well as SPIM4. We want to add UART over USB and I was able to port...
Hello, we're currently developing BLE devices with PCA10040 and nRF Conenct SDK 2.9.0.
During a series of experiments, we found that with the same hardware and the same...
Hi
I am try to developing ble mesh gateway to connect and controll different nodes using nrf52840. Please give guidline to do this. I think proxy node is bridge of host...
Hi,
I am trying the system_off sample of Zephyr version 4.0.99: https://docs.zephyrproject.org/latest/samples/boards/nordic/system_off/README.html
The sample works...
Can the NRF54L accept a CMOS output clock signal on XL1? The NRF52s could do this via clock source register settings but such a configuration is not listed in the NRF54 datasheet...
Hi,
I am trying to use nfc_t4t_lib and I have some issues because processing incoming data takes some time (around 100 ms) and therefore sending the response occurs late...
Hello, I have been going through the DFU and FOTA lesson in the Nordic intermediate course. I see that there is a FOTA support for a scenario in which we want to update a...
Good day,
I tried to build the standard Nordic application: Blinky for the nrf52840dk/nrf52840 board from the following directory on my PC: c:\ncs\v2.9.1\zephyr\samples...
Hi
I have one nordic nRF54L15 DK using as peripheral, I want to know the power of it. Thus, I use PPK2 to be a 1.8 voltage source and connect VOUT to P6 pin 1 and GND to...
Hello Team,
I have flashed the bap_unicast_server bluetooth sample on my nRF5340 Audio DK. No build or flash errors. When I connect to my phone it connects properly. I'm...
