Is there an AT command (For modem firmware >= 2.0.2) that can be used to validate whether the LTE modem can communicate with an external MIPI RFFE switch (for example on a...
Can Nordic share specific instructions on how to enable hardware tracing?
I've received the following patch from Tomasz, however I still see "trace clock missing" in Ozone...
Hi
our last product is based on nRF5340 and now we start a new design based on nRF54H20, and its essential for our design, i checked alot but there is no datasheet, reference...
NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
Dear all,
I stubled upon the following issue when developing a BLE sensor product. When I try to bt_gatt_notify(); With only one characteristic, there is not an issue...
I was looking into the sdk provided by nordic for nrd52840Dk board and want to test the zigbee protocol. I havn't find any sdk for that.
Can you share me some links and...
Hi,
I tried to get the sample ble_app_uart to work on NRF51422_DK with the S130.2.0.0 soft_device.
The compilation and programmation of the board is OK.
The soft run...
Hi all, i recently posted some topics about my application to receive support, everything went good but now i need to add a last step to the project, and i would like to have...
I am using nordic_sdk_10 for PCA10001. what are the BSP changes and config changes needed after replicating PCA10028 for DFU over UART.
I just changed CFLAFS & ASM FLAGS...
Hi,
I am storing data using pstorage module but when i power off my nrf51-dk board, the contents get deleted and not retained in memory. What could be the reason for that...
Hi,
For a new design with nRF51822-QFA, planning to use Johanson Balun and Chip antenna as shown in attached diagram. Not using any tuning components between Balun and...
Hi,
I was wondering why DFU_IMAGE_MAX_SIZE_BANKED is calculated as
(((DFU_REGION_TOTAL_SIZE/2) - DFU_APP_DATA_RESERVED))
and not
((DFU_REGION_TOTAL_SIZE - DFU_APP_DATA_RESERVED...
Hi, I'm using ble_app_uart application from latest nRF52 SDK on IAR compiler 7.1 and PCA10040 board.
It loads and runs debug code, but it does not add breakpoints on any...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Heading ##Here my PCA1000 board is getting detected in nRFgo studio even i can program and debug it, But i cant see COM PORT.
Can anybody help me out in this...
When i...
Hi,
I'm trying out the nRF52832 with kit PCA10040 V 0.9.0. I have S132 softdevice installed and running the ble_app_pwr_profiling example from nRF5 SDK v11.0.0.
I'm...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
I am trying to manage the bonds as follows. I've defined the max bonded masters as 4 on my slave. When this list gets full, I delete a random bonded master on the slave (not...
I'm trying to flash to a device with the GCC toolchain using "make -f Makefile flash_softdevice" and nrfjprog fails with the message "ERROR: There is no debugger connected...
