Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi,
Can the nRF52832 support higher data rates:
UART TX baud rate of more than 1Mbps, such as 3 Mbps without bitbanging.
TWI of 1MHz
any trick to get them...
Hi,
I recently purchased the NRF52 DK. I'm using the ble_uart_example for the SDK 11. I'm using the softdevice PCA10040.
I noticed the the SDK 11 includes the RTT c...
I want to use the nrf52840 with DCDC in high voltage mode to drive the circuite directly from a LI-ION battery.
Is there any reverse current protection built into the chip...
When you start a receive task, what will the radio do if the HFXO is not stable? Not begin to ramp up until the HFXO is stable, OR begin to ramp up but not become active until...
nrf52832, returns an error even with parameters
IROM1: 29000 57000, IRAM1 3CC8 C338, softdevice_enable() works without errors.
#define PERIPHERAL_LINK_COUNT 1
#define...
im working on nrf51822 using sdk 9 ....i completed bonding using ble proximity example without privacy key.....now i wish to add privacy key ..what all changes i have to make...
I'm using the with SDK version 13.1.0 along with S140 SoftDevice v 5.0.0-3.alpha and trying to utilize the Bluetooth 5 Extended Advertising feature.
The function ble_advdata_set...
I'm periodically polling a TWI sensor with a blocking call, as in
ret_code_t err_code;
m_xfer_done = false;
err_code = nrf_drv_twi_tx(&i2c, address, subAddress, 1,...
My external application processor UART, every 5 ms @ 19.2 KBPS transmits a byte to UART RCV of NRF8001, which needs to convert this to BLE and then transmit to a cell phone...
Hello All,
I am working on nrf52832 and i designing the custom board for the same for my application , which all pins i need to select as programming pins to dump the code...
I'm trying to figure out why "some" (as in not all of them) Android Devices drop my Bluetooth Low Energy connection (to an NRF52 which I don't think is the problem) after...
I'm trying the example border router using 2 x nRF52840 boards one with CLI and the other with NCP connected to a PI. I can get ipv6 addresses and get them to ping each other...
Hi, I am trying to control an Omnivision Camera module using the nRF51822 EK. The module uses their proprietary SCCB protocol, which is very similar to I2C. However, there...
