Hi folks,
I'm having some UART trouble - help would be much appreciated, and thank you in advance.
------------------------
Overview:
I'm working on a project that...
Hi,
We are using the nrfconnect for thread and zigbee 3.2.
We have modelled our Bluetooth peripheral, running on the nrf52840, on the BLE UART example. It connects fine...
I have installed nrf-command-line-tools_10.24.2_amd64 and jLink_Linux_V794e_x86_64 on Ubuntu 22.04. I have also installed nrfconnect-5.0.2-x86_64 for desktop and the Toolchain...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Sorry if this is too off topic, I actually don't have any problem with my nrf52840 dongle, but the App I'm communicating with. But maybe someone of you has run into the same...
I ran into the issue where the clock definitions were defined in both the "board_pcaXXX.h" file and the sdk_config.h.
e.g.
NRF_SDH_CLOCK_LF_XTAL_ACCURACY
NRF_SDH_CLOCK_LF_SRC...
the signal flow is as follow:
TLV320AIC23B(as ADC)——》nRF52832（TX）——》nRF52832（Rx）——TLV320AIC23B（as DAC）
TLV320 works in master mode and nRF52832 works in slave mode. 48kHz...
Hi all,
I would like to know how to cross compile the pc-ble-driver-py for arm target.
Do you please have a prooceding tutorial for this activity?
Thanks in advance...
Hello everyone,
I have both the NRF52840 and NRF52832 dev kits. I was wondering if Nordic has released a packet sniffer to use with Bluetooth 5.0.
Is it firmware/software...
Hi,
i am using ble_app_hrs_c_pca10056_s140(nRF52840) and i want to stop execution of my program and based on button press return i want to continue my program.
i am unable...
Hi!
When I scan for BLE devices using "nrf UART 2.0" application I get a list of all available BLE devices. While running that application a bluetooth is activated on smartphone...
I'm having a few issues getting my application to run. I'm using Eclipse/gcc configured to use managed makefiles, following the tutorial here: bitknitting.wordpress.com/....
Hi
As we know, the mesh network is contained of a number of nodes, so, if we want to get the message of the nodes on the network , i think the node which is connected with...
Hi everyone,
I'm totally newbie, and was following the tutorial devzone.nordicsemi.com/.../ . (I have two board, PCA10028 with a nRF51 and PCA10040 with a nRF52)
and...
Hi,
I have a question about scan window and interval [I'm using nrf51822aa with s130 2.0.1... I performing some tests and I find a use case: If I set both of them (scan...
Hi!
I've found out that, according to this specification
www.bluetooth.com/.../16-bit-uuids-for-members
16bit uuids can be bought by companies.
But, on the other hand...
Hi,
I have an application with an accelerometer. This one communicate in I2C (TWI ). The accelerometer send a "data ready" signal every 20ms. I'm using the GPIOTE module...
Hello,
I'm running into trouble when doing a DFU of the app only using Secure Bootloader SDK13.
When it uses Bank1, it loads the whole image to the empty space after...
We recently decided to use the Nordic nRF52840 . Given the nature of the use (BLE + Thread) of this device we were asked to use Segger Embedded Studio as our development platform...
