I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
NRF52,S132 soft device,
I am trying to toggle GPIO 10 (NFC pins Enabled as GPIO)in a 1us Timer, But its not happening , What may be the issue? Am using Timer 4. What is the...
I have programmed nrf51-dk with an example code available at mbed platform,everything works fine except that the ble is visible even if we open bluetooth menu.It is scanned...
Hi,
I'm developing something with NFC / BLE handover - it is currently working fine, NFC tag is read by a phone, nrf52 starts advertising and phone then connects to it over...
Hello,
I'm remaking an nrf52 project in Keil and ran into an issue when it came to compiling. All of the errors outputted have came from bsp.c, mostly stating that a few...
Hi,
We will use nRF52 along with small 8bit micro and UART connection. The MCU cannot support standard baudrate 115200, and we will need to implement non-standard speed...
I am using the Johanson balun ( www.johansontechnology.com/.../Johanson_nRF8001_App_Note_v2.pdf) to interface the differential input of the nRF8001. The PCB manufacture I...
Hello,
I am using the following function call to set up PWM:
app_pwm_config_t pwm1_cfg = APP_PWM_DEFAULT_CONFIG_2CH(5000L, BSP_LED_0, BSP_LED_1);
However, the compiler...
Hello,
I designed a board with a nrf51822 on it. My problem now is, that this chip needs far too much current (with no firmware on it) when I apply the 3V3 power to it. I...
I have been working on a project that involves two nrf51 dev boards, one is acting as a central and the other is acting as a peripheral, and I have been encountering a problem...
Hello!
For beginning with nRF51 I chose BLE Nano set of boards (BLE Nano + MK20 USB donbgle) and it was of great help to easily begin with BLE.
So far, we came to the need...
As an experiment, we want to implement soft power off for nRF52 with external components. We want to keep the entire circuitry entirely switched off, and after a press of...
I do not use board.h nor bsp* in my project, and also I am not initializing the pins that I do not use in my program currently - so P0.17 is not initialized and setup. However...
