Hi, I am running openthread on the NRF54l15 DK. Whenever I am debugging and hit the breakpoint or pause the program, then on resumption my app crashes. How Can I debug while...
Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command: west build --build-dir build . --pristine --board nrf54l15dk...
I want to confirm how much current is being drawn from the battery while the nRF52 is in it's absolute lowest power state and waiting for an NFC field to wake it up. From...
I am interested in setting the tx power level the advertising packets in a nRF52832 are transmitted with. I saw there is the TXPOWER register in the RADIO section (address...
I have a use case where sensors on a BLE peripheral need to push notifications to a BLE central indeterministically. So it needs to keep the connection always on. The notification...
Hi,
I tired Nordic Uart Service example on Nexus 5 Android ver 5.1.1, but I am not able to connect. I am able to connect to Samsung S6 and Nexus Android ver 4.4.4. I am using...
Hi Nordic,
I've try many times but no luck, I have a PCA10028, which works fine with SDK8~10 and S110.
Recently I found the SDK has become ver11 and SD turn to S130. So...
What is the best method for sending long data to ble_app_uart from android? We tried sending data by breaking into 20 bytes chunks and used thread.sleep() between each packet...
When I'm using the SDK 6.1.0, the twi drivers works while and I can easily understand the twi work flue. Howeve, the SDK 11.0.0 changed the twi drivers. I don't know what...
Hi Nordic,
I am using PCA10000 v2.2.0 with MCP and FW "MEFW nRF51822 0.11.0"
I just tried the "nRF Connect" under Windows 10 and fail to use it. Below is my steps:
...
Hi All,
I'm using nrf52 PCA10040 v 0.9.0, with SDK11. No softdevice being used in this case.
While exploring using EasyDMA with the SPI peripheral, the example in sdk11...
Hi there,
this problem may extend the scope, as it relates the SPI slave device (atmel winc1500). When I run the SPI master example, I can see the data transmitted on oscilloscope...
Hi, I use S110 v8 in my application with DFU support. When DFU is triggered from application (by writing 0x0104 to DFU service control characteristic), then application fails...
Working on a project i want to update the nordic application (firmware) from other MCU, i am having some problem to compute the crc.
How to we calculate the crc of...
When I plug the nRF51822EK (PCA10024) in via USB while holding the reset button down, it mounts as "MBED LOADER" rather than "MBED". This page
developer.mbed.org/.../ ...