Hi,
I am trying to build bluetooth hci_uart sample for esp32 board and haven't had much success so far. I am running this command to build:
`west build -p always -b...
I'm using NCS SDK v3.0.2 and trying to build the Matter Thermostat example for the target: ` nrf54L15DK/nrf54L15/cpuapp/ns ` However, the build fails with the following errors...
when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
Hello,
I am using an nRF9160 to connect to a private network. My nRF9160 successfully attaches to this network.
However, when reviewing the logs from the private network...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
Hi, I'm currently trying to add an Actinius Icarus IoT board as LTE device at nRF cloud.
I already know my board IMEI (I got it by flashing the AT client sample and then...
Connecting nrf21540 to a nrf52840. 840 GPIO default state is input, input buffer connected. One of the 840 GPIO pins is connected to the 540 PDN pin.
1) If the 840 gets...
I would like to build a avdertising node for the public usage. So without previous bonding everybody should take the advertising through mobile application. Application is...
Hi all,
I use the nRF2402 to do communicate with nRF24L01+.I have read the all the information from Product_Specification_nRF2402_2_2,
but I still know how to set the...
hello everyone,
i am studying about BLE i found that there are two types of advertising packet formats in LINK LAYER one format is there, in GAP one format is there, on...
Hello,
Is there a way to find out the currently used connection interval when configured as a server?
I only found the function sd_ble_gap_ppcp_get which provides the...
Hi,
I have created two proprietary characteristics with notification property to notify some data's using these two characteristics when some event occurs. I can able to...
Dear developer zone,
I am using nRF51822 with soft device and SDK 4.4.2
My device return an error on disconnection when the ble_bondmngr_bonded_masters_store function...
Hello,
I want to test my circuit using a CR2032 coin cell. Is there any way to jumper a coin cell into the supply on the nRF6310 and bypass the voltage regulator/RS232...
Hi,
I am curious what is the main difference between nRF8001 and nRF8002.One is for connectivity and the other is for proximity. However, I would like to develop an application...
i need a help with the attenna design. here is the eagle files, i'm not sure it is fine. i used a Balun BAL-NRF01D3 and my board thickness is 0.6mm. i need to know the copper...
I got the nRF51822 DK and tried hooking up the dongle. I am using Windows 7 32 bit. When I plugged the dongle into a USB port, there is a “JLinkCDCUARTPort（COM19)” added to...
Hi,
My device is always in bootloader mode, even if i flash the sample heart rate application it is not entering into the application. Actually, before it was working fine...
Hello,
I am planning to develop an application in which I need to do some image processing (probably using open CV libraries), and I would like to know if the nRF51822...
I see in the example code there is
#define FLASH_PAGE_SYS_ATTR (BLE_FLASH_PAGE_END - 3) /**< Flash page used for bond manager system attribute information. */
#define...
I'm using NRF51822 and I have some question about the ble connection:
according to BLE 4.0 spec, when Tsup(connection supervision time) reaches, connection lost is considered...
