I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello ,
I have an idea of using nrf51DK along with another external microcontroller both of them are connected via SPI inerfacing the aim of my question can i use the bootloader...
Hi, I am working on Eddystone project i.e nrf5-sdk-for-eddystone-master now I need to add the dfu support to it the problem I am facing is explained below
In SDK nRF5_SDK_11...
Hi,
I am using nRF51422 with S130. I want my application to blink a LED every one second. For now I am using App Timer which solves the purpose but the current consumption...
Hi, I have been trying to figure out how to get the IF BOOT/RESET button on the nRF52 micro-controller working. I have defined "CONFIG_GPIO_AS_PINRESET" under C/C++ in the...
Hi all,
I seek an advice on the passkey topic. Have been researching the topic all day but still have some confusion. I am running SDK 10.0 ble_app_uart example on nRF51...
I have a quick question pertaining to the instruction sequence that occurs immediately after the anti-collision completes:
I am working on implementing a Type-4 tag library...
Following this thread , I tried to upgrade my dongle from s130 v1.0 to s130 v2.0.
I'm using windows driver 0.5.0
Tested both binaries for 0.5.0 downloaded and compiled...
Hey all,
What I am trying to achieve today is setting RAM retention on nRF52.
As it is stated in Product Specification of nRF52, RAMON register is deprecated ans shouldn...
I have 2 nrf51-dk with softdevice 130 (one as central, and the other as peripheral), i use sdk v.10.
I have read and follow central tutorial , and all works.
Now, I...
hi,
i want to use 51822 timer counter to capture external pulses，how can i config the capture task?
in the nRF51 Series Reference Manual, it is say
The TIMER implements...
Hi All,
We have been developing device with pca10028 evaluation board and in the process we use also few other custom boards with nrf51822. We use IAR. The device system...
Is there any recommended value for PSTORAGE_MIN_BLOCK_SIZE or is it completely system determined. The commends in pstorage_platform.h are somewhat unclear.
If I only require...
Hello.
I want to migrate function of "sd_ble_gatts_value_set" to nRF52 from nRF51.
I use nRF52832 ,S132 and PCA10040.
I saw documentations about the function.
infocenter...
Hi. I'm using PCA10028, SDK10.0.0, S130.
I want to go to nrf_drv_uart_uninit(); right after sending data.
in order to save current consumption.
So I made source code...
