But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
My scenario is I have an android device and 100+ advertising nrf52 devices. Is it possible android to receive/scan advertising packets (small) from 100+ devices which mean...
error occurs in nrf_delay.c of nrf52832
Because there are ASM in nrf_delay.h
nrf_delay.c:
#include <stdio.h>
#include "compiler_abstraction.h"
#include "nrf.h"
...
Hello,
I cannot find an example in the current SDK on how to use APP_UART. I do not want to use app_uart_fifo because it has quite some overhead that I do not need. All...
I am using nRF5_SDK_11.0.0_89a8197 to test esb maximum throughput.
in the macro definition of NRF_ESB_CREATE_PAYLOAD,
#define NRF_ESB_CREATE_PAYLOAD(_pipe, ...)
...
On the nRF51, there are 5 OVERRIDE registers (0-4) in the radio module.
What do those registers do and when should they be used? The FRM was not clear about them.
From what I can see the scenario where you have a serialized app running from a separate CPU and how to do firmware update on that is not discussed anywhere on the Nordic...
ToSendTONordic.zip
Hi,
I am using s130-nrf51822xxa. I tried GPIOTE example and it works fine. I tried ble_uart example and it works.When I try to combine both of them...
As of API level 21 BluetoothGatt#requestMtu can be used to go beyond the limit of 23 bytes GATT_MTU_SIZE_DEFAULT. Will the SDK support such enhancements one day?
In BLE notification i am getting 31 byte data but it comes in two packets 20 byte + 11 bytes continually.How do i get last 11 byte data which comes in 2nd packets after 2s...
Hi,
i want to test the Server feature of the Master Control Panel 3.10.0 together with a nrf51 Dongle. By pressing start under File->Server setup the server starts, but...
Hi I have problem with LFCLK timer. In os_tick_init() in RTX_Conf_CM.c there is a loop and it won't end.
while (NRF_CLOCK->EVENTS_LFCLKSTARTED == 0)
{
Do nothing.
...
gaps.zip
Hi,
I have a code that continuously toggles a pin(I use nrf_drv of gpiote+ppi+timer2 for this purpose and interrupt time = 30usec). I have basically taken the...
I know the things like the TWI allow you to send additional data when you instantiate a transacation. Is there any way to do a similar thing with UART?
I'd like to pass...
