Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello everyone,
currently I'm working on a project with an NRF51-SoC. I want to use a MEMS Oscillator as high frequency clock source this is working very well so far. But...
I have 500 nrf51822 devices, when I use Master Control panel to scan twice, the first time I can scan device A, the second time I can not scan out device A.
I google find...
Hello,
My understanding is that you can use the nRFToolBox app to upload code using OTA DFU.
But this looks cumbersome, as you have to first get the hex file on to the...
I built the ble_app_uart example app using GCC with nRF5_SDK_11.0.0_89a8197, and on testing it with the latest version of Nordic nR ToolBox (iOS) and nRFMaster Control Panel...
Hi,
I want to save settings in the memory.
In my case, the softdevice is enabled, there is no ble advertising.
I use pstorage functions.
Problem: I stored 0x12, 0x23,...
Hi,
I'm running a nRF51422QFAC and using sd_temp_get() to read the chip temperature twice / second.
I put it in a temperature chamber and swept the temperature from...
Dear members!
I followed the tutorial of the nRF8001, and tried this code: learn.adafruit.com/.../nrf-uart-in-detail
It worked for me just fine, but...
I have an...
Hi there,
I'm attempting to use the UARTE for a continuous read scenario but I am noticing there is significant delay between the STOPRX task and the ENDRX interrupt (...
Hi,
I'm trying to get a custom PCB working. I can use either the plain peripheral UART, or the ble-app-uart example projects on the NRF52-DK and they work, but they don...
I am using the nRF52 Preview kit (PCA 10036 board) and SDK 0.9.2. Up to this point, I have been able to do everything I want with TWI using the hardware driver. This time...
I tried measuring idle current for nrf51422 board and got something about 1900 uA using multimeter without resistor and with bridge SB9 cut. I know the value is too high....
Dear all:
error occured when I was programming application hex in nRFgo Studio1.20.0,just refer to "program application error.png" ,the error shows "programming failed...
I have a sensor device that needs to transmit every so many seconds. I am looking for a code example to run on nRF52-DK that will do this, sleeping inbetween transmissions...
According to the Gazell using the 1MHz spacing for each channels and the DTM using 2MHz spacing.
Then can we use the DTM channel 0 for Gazell channel 2 to test the Frequency...
