Dear reader,
I am currently working on a project using the NRF54L15 MCU. There is plenty of documentation available for this component, and the reference circuitry for the...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Hi everyone,
I'm working with the nRF9160 and trying to configure P0.19 as the UART TX pin using Zephyr. Here's the configuration I used in the device tree:
uart1_default...
I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
Hello,
I am using nRF Connect SDK v3.0.1, together with the Find My add-on. Test case TCG013 of the Find My Network Self-Certification Test Cases R1.7 is failing on the...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
HI: D:\ncs\v3.0.0\nrf\samples\bluetooth\peripheral_uart Using the nrf54l15DK board can run peripheral_uart examples,connection is disconnected. However, when I use the nrf54l05...
I am facing the same issue regarding to this post "Custom Service Issue - devzone.nordicsemi.com/.../".
At least i could figure out the IRAM1 start and size as explained...
Hi there!
I have been working with serializer and have the below issue:
I am using sd_ble_gatts_hvx() to transfer 20 bytes in burst until I get an error (TX buffer full...
Hi all,
first I have to admit that I'm a total rookie in "electricity". I know BLE software-side but just started to learn the hardware stuff.
I just received my PPK and...
by writing servals data into flash ,the data is always is 0,
void fstorage_test(void)
{
ret_code_t ret = fs_init();
if (ret != NRF_SUCCESS)
{
bsp_indication_set...
HI,
I am using nrf52832 with softdevice 132. Using SPIS1 to get the sensor datas from nrf to AARDVARK for calibration. Whenever I send the data's from aardvark(using AArdvark...
Whenever I try to flash the device in keil, I get a no Jlink device found. I get a similar message when trying to connect to the device via Segger. nrfGo Studio just does...
hello:
i want to use pwm in SDK9.0, in my project ,i need to send a cmd to nrf51822-QFAA,and then it control the motor on ,and with this cmd ,i should contrl pwm to let...
Can I control the music player by simulate a hid device
now our customer ask for a new function--use bracelet control the music player>> last next vol+- ...
but the app...
Hi,
I am trying to develop the ble_app_template project into a custom ble application.
Where is says
/* YOUR_JOB: Declare all services structure you application is...
Hi Dear Engineers!
I use nRF52840 SPI (slave) to communicate with Master (HOST) CPU.
if I stop any ADV / SCAN RF functions all works Great!
But if I start ADV (or...
Hi,
I am having some trouble in setting up the RedBearLab BLE board w/ nRF51822 that i recently bought for a project I am currently doing . I am using windows OS, with eclipse...
Folks,
Attempting to use a sample app from the 13.0.0 SDK for a pointing (mouse) device I'm prototyping, located at ...\nRF5_SDK_13.0.0_04a0bfd\examples\ble_peripheral...
I use the sdk 13.0.0,software device s332,I hope the rtc can work when cpu sleep,and the lowest working current need less than 10uA,what should i do?or Is there a reference...