Hi,
nRF5340 and SDK v3.0.0 I'm using.
Currently my nRF5340 based BLE device can be bonded with smartphone via passkey, after bond is done, the device stops advertising...
hi everyone
After using Android nRF Connect FOTA, the settings storage partition of my device was erased, which means that my device's PAIR information was lost and the...
Hi Nordic Team,
I'm looking to use the UICR->OTP region ( One Time Programmable (OTP) memory region within the User Information Configuration Registers (UICR)) on the nRF54H20...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Due to production requirements, I need to obtain the device's QR code. However, I found that the QR code can only be retrieved using the code snippet below after calling Nrf...
Hi Nordic Support Team,
I'm currently experimenting with Channel Sounding using a couple of nRF54L15 boards.
I am trying to obtain raw I and Q samples so that I may analyze...
Hello,
currently i am configuring the networking stack on my project.
The goal is to use Matter's built-in Thread connection, to establish a Secure CoAP connection. I...
Hi!
My problem is that my code works on the devkit PCA10004(PCB antenna) but not on my own custom board.
The devboard can be connected to and all characteristics can be...
Hello,
i would like to make device which will be dynamically change connection with centrals. It should be connected to the nereast device (with the most power). So I will...
Hi,
I am currently using this example code (pasted below). It is sending the character 'a' every 4 seconds. I can't figure out which part of the code defines the character...
Attached is the schematic of my part configured for low voltage mode.
Very close to page 62 in the nRF51822 product specification document.
I am externally feeding 1.8V...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
We start to migrate our equipment from nrf14L01 receiver to nrf51422 receiver in order to serve more equipment.
I am using nrf51822 to receive propietary protocols from heart...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
hi Ole Morten:
thank you for your great support.
i have tested nrf6310\temperature_example. at 30(Celsius)
I checked the data. NRF_TEMP=0x000002AF; TEMP=0xFFFFFFAC;...
Hi,
I need help on calculating the current consumption of our device when it is in advertise mode. So please answer the below questions.
What are all the significant...
Hello,
i would like to use HRM, HID, BAS and DIS profiles simultaniously. I used HID mouse example. I append required HRM things and it work almost properly. Problem is fault...
Hi, I'm a beginner. I want to add to example of the proximity, next service identical to battery service. I need to send 1 byte of data.
Everything works well until when...
I have an application that reads an nRF51822 pin configured as analog input and then sends that value using "ble uart" (included in Nordic's sdk). Analog input is read in...
Been studying the S110 5.x -> 6.0 migration docs. Are there any project-specifics / include-paths / Keil build-settings that must be updated as well?
Do I understand it...
Im stuck that i can't get my Motherboards to update. Just goes into an endless loop of saying toggle power to rest it, starting boo loader, Couldn't start.. etc etc..
Attached...
